Sica 12 L1 2.5 SL
Thiele-Small parameters
| Nominal size | 12" |
|---|---|
| Impedance | 8 Ω |
| Fs | 47.5 Hz |
| Qts | 0.36 |
| Qes | 0.38 |
| Qms | 7.5 |
| Vas | 81.8 L |
| Sd | 490.9 cm² |
| Xmax | 3.7 mm |
| Re | 5.5 Ω |
| Bl | 14.2 T·m |
| Mms | 47 g |
| Pe | 300 W |
| Sensitivity | 97.3 dB |
Alignment hint
| EBP | 125 · ported |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 28.6 L |
EBP > 100: favours a ported (bass-reflex) alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| SICA PL 12 B 3 S | 46.7 -0.8 | 0.356 = | 79.3 -2.5 | 5.5 +1.8 | 97.1 -0.2 | close | + | |
| SICA 12 E 2 CS Z007660 | 47.5 = | 0.364 = | 76.9 -4.9 | 4 +0.3 | 95.8 -1.5 | close | 200 W vs 300 W: lower power handling | + |
| B&C 12 FCX 76 | 47 -0.5 | 0.339 -0.02 | 82 +0.2 | 5 +1.3 | 97.6 +0.3 | close | + | |
| SICA 12 E 2 CS | 48 +0.5 | 0.364 = | 76.9 -4.9 | 4 +0.3 | 95.9 -1.4 | close | 200 W vs 300 W: lower power handling | + |
| Faital PRO 12PR300 v2015 | 50 +2.5 | 0.357 = | 79.2 -2.6 | 4.9 +1.2 | 98 +0.7 | close | + | |
| Audax PR330T2 4 Ohms | 46.8 -0.7 | 0.354 -0.01 | 80.1 -1.7 | 3.4 -0.3 | 99.3 +2 | close | 4 Ω vs 8 Ω: amp load changes · 150 W vs 300 W: lower power handling · Xmax 3.4 mm < 3.7 mm: lower excursion-limited SPL | + |
| Eminence DELTA PRO 12 A | 51 +3.5 | 0.353 -0.01 | 81.7 -0.1 | 6.2 +2.5 | 98.1 +0.8 | close | + | |
| Eminence DELTA PRO 12 A vp | 51 +3.5 | 0.353 -0.01 | 81.7 -0.1 | 6.2 +2.5 | 98.1 +0.8 | close | + | |
| Eminence DELTA PRO 12 | 51 +3.5 | 0.353 -0.01 | 81.7 -0.1 | 3.2 -0.5 | 98.1 +0.8 | close | Xmax 3.2 mm < 3.7 mm: lower excursion-limited SPL | + |
| Eminence DELTA PRO 12A | 51 +3.5 | 0.35 -0.01 | 81.7 -0.1 | 4.6 +0.9 | 99.2 +1.9 | close | + |
Compare the closest 3 against the 12 L1 2.5 SL →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.