SICA 10 K 3 PL 8 Ohms
Thiele-Small parameters
| Nominal size | 10" |
|---|---|
| Impedance | 8 Ω |
| Fs | 55.9 Hz |
| Qts | 0.276 |
| Qes | 0.29 |
| Qms | 5.65 |
| Vas | 32.6 L |
| Sd | 346.3 cm² |
| Xmax | 4 mm |
| Re | 5.28 Ω |
| Bl | 16.3 T·m |
| Mms | 41.8 g |
| Pe | 350 W |
| Sensitivity | 96.7 dB |
Alignment hint
| EBP | 193 · ported |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 5.9 L |
EBP > 100: favours a ported (bass-reflex) alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| SICA 10K3PL | 56 +0.1 | 0.276 = | 32.6 = | 4 = | 96.7 = | close | + | |
| B&C 10 NDL 64 | 56 +0.1 | 0.267 -0.01 | 31 -1.6 | 4 = | 96.2 -0.5 | close | 250 W vs 350 W: lower power handling | + |
| B&C 10NDL64 | 56 +0.1 | 0.26 -0.02 | 31 -1.6 | 6 +2 | 97 +0.3 | close | 250 W vs 350 W: lower power handling | + |
| PHL Audio 3001 | 57 +1.1 | 0.282 +0.01 | 35 +2.4 | 3.5 -0.5 | 97 +0.3 | close | 200 W vs 350 W: lower power handling · Xmax 3.5 mm < 4 mm: lower excursion-limited SPL | + |
| B&C 10NDL64 | 58 +2.1 | 0.3 +0.02 | 34.5 +1.9 | 4.5 +0.5 | 97 +0.3 | close | 16 Ω vs 8 Ω: amp load changes · 250 W vs 350 W: lower power handling | + |
| 18 Sound 10NTLW2000 | 58 +2.1 | 0.27 -0.01 | 35.4 +2.8 | 4.4 +0.4 | 95 -1.7 | close | 16 Ω vs 8 Ω: amp load changes | + |
| RCF MB 10N251 | 55 -0.9 | 0.271 -0.01 | 38.8 +6.2 | 4.6 +0.6 | 97.4 +0.7 | close | + | |
| SICA 10 K 3 PL 4 Ohms | 56 +0.1 | 0.265 -0.01 | 29.2 -3.4 | 4 = | 98.9 +2.2 | close | 4 Ω vs 8 Ω: amp load changes | + |
| SB Audience BIANCO-10MW150 | 60 +4.1 | 0.293 +0.02 | 34.6 +2 | 4.3 +0.3 | 97.8 +1.1 | close | + | |
| PHL Audio 3420 | 53 -2.9 | 0.256 -0.02 | 35 +2.4 | 4.3 +0.3 | 97.6 +0.9 | close | + |
Compare the closest 3 against the 10 K 3 PL 8 Ohms →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.