SB Audience NERO-10MWN600D
Thiele-Small parameters
| Nominal size | 10" |
|---|---|
| Impedance | 8 Ω |
| Fs | 68 Hz |
| Qts | 0.339 |
| Qes | 0.36 |
| Qms | 5.88 |
| Vas | 18.8 L |
| Sd | 356.3 cm² |
| Xmax | 3.9 mm |
| Re | 5.4 Ω |
| Bl | 18.2 T·m |
| Mms | 51.9 g |
| Pe | 600 W |
| Sensitivity | 95.8 dB |
Alignment hint
| EBP | 189 · ported |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 5.6 L |
EBP > 100: favours a ported (bass-reflex) alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| Beyma 10MCS500 | 70 +2 | 0.366 +0.03 | 18.8 = | 4.4 +0.5 | 95.7 -0.1 | close | + | |
| B&C 10 NDL 64 vp 2022 | 68 = | 0.343 = | 21.5 +2.7 | 3.3 -0.6 | 95 -0.8 | close | 250 W vs 600 W: lower power handling · Xmax 3.3 mm < 3.9 mm: lower excursion-limited SPL | + |
| B&C 10 NDL 64 vp | 71 +3 | 0.361 +0.02 | 19 +0.2 | 3.1 -0.8 | 95.9 +0.1 | close | 250 W vs 600 W: lower power handling · Xmax 3.1 mm < 3.9 mm: lower excursion-limited SPL | + |
| P.Audio SN-10MB | 70 +2 | 0.397 +0.06 | 19 +0.2 | 5 +1.1 | 95.6 -0.2 | close | + | |
| 18 Sound 10NTLW2500 | 65 -3 | 0.33 -0.01 | 21 +2.2 | 7.6 +3.7 | 96.5 +0.7 | close | + | |
| Sica 10 K 4 PL | 62.5 -5.5 | 0.31 -0.03 | 19.5 +0.7 | 5 +1.1 | 94.9 -0.9 | close | + | |
| B&C 10NW76 | 68 = | 0.29 -0.05 | 18.5 -0.3 | 7 +3.1 | 96.8 +1 | close | 16 Ω vs 8 Ω: amp load changes · 400 W vs 600 W: lower power handling | + |
| Faital PRO 10FH530 | 67 -1 | 0.39 +0.05 | 20.2 +1.4 | 7.45 +3.55 | 96 +0.2 | close | 16 Ω vs 8 Ω: amp load changes | + |
| B&C 10CXN64 | 68 = | 0.31 -0.03 | 23 +4.2 | 5.5 +1.6 | 95.2 -0.6 | close | 250 W vs 600 W: lower power handling | + |
| B&C 10NDL88 | 67 -1 | 0.32 -0.02 | 15.6 -3.2 | 7.8 +3.9 | 95.5 -0.3 | close | 16 Ω vs 8 Ω: amp load changes | + |
Compare the closest 3 against the NERO-10MWN600D →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.