RCF MR 10N301 v2016
Thiele-Small parameters
| Nominal size | 10" |
|---|---|
| Impedance | 8 Ω |
| Fs | 250 Hz |
| Qts | 0.648 |
| Qes | 0.72 |
| Qms | 6.48 |
| Vas | 2.2 L |
| Sd | 350 cm² |
| Xmax | 0.7 mm |
| Re | 6.2 Ω |
| Bl | 20.7 T·m |
| Mms | 31.6 g |
| Pe | 300 W |
| Sensitivity | 99.9 dB |
Alignment hint
| EBP | 347 · ported |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 11.5 L |
EBP > 100: favours a ported (bass-reflex) alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| B&C 10NSM76 | 235 -15 | 0.66 +0.01 | 2 -0.2 | 3.5 +2.8 | 99 -0.9 | usable | 16 Ω vs 8 Ω: amp load changes | + |
| RCF MR 10N301 | 248 -2 | 0.603 -0.05 | 3.2 +1 | 0.9 +0.2 | 99 -0.9 | usable | 16 Ω vs 8 Ω: amp load changes | + |
| B&C 10NSM76 | 235 -15 | 0.52 -0.13 | 2 -0.2 | 3.5 +2.8 | 100 +0.1 | usable | + | |
| Beyma 10MCF400Nd | 270 +20 | 0.455 -0.19 | 1.8 -0.4 | 0.6 -0.1 | 102.1 +2.2 | usable | Xmax 0.6 mm < 0.7 mm: lower excursion-limited SPL | + |
| Beyma 10"MCF400Nd | 260 +10 | 0.44 -0.21 | 2 -0.2 | 3.5 +2.8 | 102 +2.1 | usable | + | |
| Eminence LIL BUDDY | 149 -101 | 0.843 +0.19 | 10 +7.8 | 0.8 +0.1 | 98.5 -1.4 | risky | 50 W vs 300 W: lower power handling | + |
| Jensen P10/100BB | 112.1 -137.9 | 0.804 +0.16 | 14.1 +11.9 | 1 +0.3 | 96.9 -3 | risky | 100 W vs 300 W: lower power handling | + |
| Celestion G10 | 129 -121 | 0.92 +0.27 | 12.3 +10.1 | 0.8 +0.1 | 94.2 -5.7 | risky | 16 Ω vs 8 Ω: amp load changes · 30 W vs 300 W: lower power handling | + |
| Peavey S-10825 | 102 -148 | 0.671 +0.02 | 14.6 +12.4 | 2.7 +2 | 96.7 -3.2 | risky | 200 W vs 300 W: lower power handling | + |
| Celestion G10 GREENBACK | 94.9 -155.1 | 0.471 -0.18 | 12.9 +10.7 | 0.8 +0.1 | 95.7 -4.2 | risky | 30 W vs 300 W: lower power handling | + |
Compare the closest 3 against the MR 10N301 v2016 →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.