RCF LF15N451
Thiele-Small parameters
| Nominal size | 15" |
|---|---|
| Impedance | 8 Ω |
| Fs | 35 Hz |
| Qts | 0.18 |
| Qes | 0.19 |
| Qms | 4.2 |
| Vas | 125 L |
| Sd | 900 cm² |
| Xmax | 9 mm |
| Re | 5.1 Ω |
| Bl | 33.5 T·m |
| Mms | 171 g |
| Pe | 1300 W |
| Sensitivity | 97 dB |
Alignment hint
| EBP | 184 · ported |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 8.7 L |
EBP > 100: favours a ported (bass-reflex) alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| 18 Sound 15NLW4500 | 35 = | 0.2 +0.02 | 126 +1 | 14.5 +5.5 | 96.6 -0.4 | close | 4 Ω vs 8 Ω: amp load changes | + |
| RCF LF 15N451 | 35 = | 0.182 = | 125 = | 6.6 -2.4 | 98.4 +1.4 | close | Xmax 6.6 mm < 9 mm: lower excursion-limited SPL | + |
| Radian 2216Neo | 40 +5 | 0.19 +0.01 | 114 -11 | 9 = | 96.5 -0.5 | close | 800 W vs 1300 W: lower power handling | + |
| B&C 15NW100 | 33 -2 | 0.22 +0.04 | 139 +14 | 9 = | 97 = | close | 1000 W vs 1300 W: lower power handling | + |
| B&C 15NW100 | 34 -1 | 0.23 +0.05 | 126.1 +1.1 | 9 = | 95 -2 | usable | 4 Ω vs 8 Ω: amp load changes · 1000 W vs 1300 W: lower power handling | + |
| B&C 15DS115 | 33 -2 | 0.17 -0.01 | 94 -31 | 16.5 +7.5 | 97 = | usable | + | |
| B&C 15 SW 115 | 35 = | 0.237 +0.06 | 110 -15 | 8.8 -0.2 | 96.6 -0.4 | usable | Xmax 8.8 mm < 9 mm: lower excursion-limited SPL | + |
| RCF LF15N401 | 34 -1 | 0.22 +0.04 | 160 +35 | 9 = | 97 = | usable | 900 W vs 1300 W: lower power handling | + |
| Faital PRO 15XL2400 | 32 -3 | 0.21 +0.03 | 113.9 -11.1 | 17.67 +8.67 | 96 -1 | usable | + | |
| Oberton 15PD601 | 38.2 +3.2 | 0.228 +0.05 | 133.31 +8.31 | 8.5 -0.5 | 98 +1 | usable | 600 W vs 1300 W: lower power handling · Xmax 8.5 mm < 9 mm: lower excursion-limited SPL | + |
Compare the closest 3 against the LF15N451 →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.