RCF LF 18N405
Thiele-Small parameters
| Nominal size | 18" |
|---|---|
| Impedance | 8 Ω |
| Fs | 30 Hz |
| Qts | 0.324 |
| Qes | 0.34 |
| Qms | 7 |
| Vas | 227 L |
| Sd | 1220 cm² |
| Xmax | 10.8 mm |
| Re | 4.9 Ω |
| Bl | 26.5 T·m |
| Mms | 258.7 g |
| Pe | 1500 W |
| Sensitivity | 96.7 dB |
Alignment hint
| EBP | 88 · flexible |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 60.3 L |
EBP 50-100: works in either a sealed or ported alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| RCF LF18N405 | 30 = | 0.32 = | 227 = | 14 +3.2 | 97 +0.3 | close | + | |
| BMS 18N850vv2 | 29.8 -0.2 | 0.33 +0.01 | 243 +16 | 12 +1.2 | 95 -1.7 | close | + | |
| Ciare NDH18_4S | 31 +1 | 0.319 -0.01 | 239 +12 | 9.4 -1.4 | 96.5 -0.2 | close | 1000 W vs 1500 W: lower power handling · Xmax 9.4 mm < 10.8 mm: lower excursion-limited SPL | + |
| RCF LF18N408 | 30 = | 0.33 +0.01 | 193 -34 | 15 +4.2 | 97 +0.3 | close | + | |
| Beyma 18SW1600ND | 32 +2 | 0.33 +0.01 | 205.7 -21.3 | 10 -0.8 | 96.6 -0.1 | close | Xmax 10 mm < 10.8 mm: lower excursion-limited SPL | + |
| Sica 18 S 4 CP | 33 +3 | 0.35 +0.03 | 225 -2 | 11 +0.2 | 97.1 +0.4 | close | + | |
| RCF LF 18N408 | 30 = | 0.327 = | 193 -34 | 9.8 -1 | 96.3 -0.4 | close | Xmax 9.8 mm < 10.8 mm: lower excursion-limited SPL | + |
| RCF LF 18X451 | 30 = | 0.278 -0.05 | 220 -7 | 10.7 -0.1 | 96.8 +0.1 | close | Xmax 10.7 mm < 10.8 mm: lower excursion-limited SPL | + |
| Lavoce SAF184.03 | 30 = | 0.32 = | 260 +33 | 13 +2.2 | 94.9 -1.8 | close | + | |
| Fane COLOSSUS 18-1000 | 32 +2 | 0.319 -0.01 | 236 +9 | 8.9 -1.9 | 97 +0.3 | close | 1000 W vs 1500 W: lower power handling · Xmax 8.9 mm < 10.8 mm: lower excursion-limited SPL | + |
Compare the closest 3 against the LF 18N405 →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.