RCF LF 15X401 v2013
Thiele-Small parameters
| Nominal size | 15" |
|---|---|
| Impedance | 8 Ω |
| Fs | 41.8 Hz |
| Qts | 0.313 |
| Qes | 0.33 |
| Qms | 6.07 |
| Vas | 116.4 L |
| Sd | 902 cm² |
| Xmax | 8.7 mm |
| Re | 4.99 Ω |
| Bl | 23.8 T·m |
| Mms | 142.1 g |
| Pe | 1500 W |
| Sensitivity | 98.1 dB |
Alignment hint
| EBP | 127 · ported |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 28.4 L |
EBP > 100: favours a ported (bass-reflex) alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| Sica 15 PF 3 | 45 +3.2 | 0.31 = | 117.6 +1.2 | 8 -0.7 | 99.1 +1 | close | Xmax 8 mm < 8.7 mm: lower excursion-limited SPL | + |
| Sica 15 S 4 PL | 39.5 -2.3 | 0.32 +0.01 | 127.6 +11.2 | 10 +1.3 | 97.8 -0.3 | close | + | |
| Beyma 15LEX1000Fe | 41 -0.8 | 0.34 +0.03 | 116 -0.4 | 11 +2.3 | 97 -1.1 | close | 1000 W vs 1500 W: lower power handling | + |
| Oberton 15NXL701 | 43.4 +1.6 | 0.3 -0.01 | 127.09 +10.69 | 9.25 +0.55 | 99 +0.9 | close | 700 W vs 1500 W: lower power handling | + |
| Oberton 15XL701 | 45.25 +3.45 | 0.28 -0.03 | 116.99 +0.59 | 8.75 +0.05 | 98 -0.1 | close | 700 W vs 1500 W: lower power handling | + |
| Oberton 15NXB1201 | 38.49 -3.31 | 0.324 +0.01 | 111.94 -4.46 | 12 +3.3 | 97 -1.1 | close | + | |
| 18 Sound 15LW2400 | 40 -1.8 | 0.3 -0.01 | 131 +14.6 | 10 +1.3 | 97 -1.1 | close | + | |
| Faital PRO 15HP1060 | 40 -1.8 | 0.31 = | 100.3 -16.1 | 12.45 +3.75 | 97 -1.1 | close | 1000 W vs 1500 W: lower power handling | + |
| 18 Sound 15LW1401 | 42 +0.2 | 0.27 -0.04 | 131 +14.6 | 9 +0.3 | 98 -0.1 | close | 1000 W vs 1500 W: lower power handling | + |
| Faital PRO 15HP1020 | 40 -1.8 | 0.27 -0.04 | 126.6 +10.2 | 9 +0.3 | 98 -0.1 | close | 700 W vs 1500 W: lower power handling | + |
Compare the closest 3 against the LF 15X401 v2013 →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.