Pioneer PAX30G vp1
Thiele-Small parameters
| Nominal size | 12" |
|---|---|
| Impedance | 16 Ω |
| Fs | 36.4 Hz |
| Qts | 0.816 |
| Qes | 0.903 |
| Qms | 8.473 |
| Vas | 122.3 L |
| Sd | 552 cm² |
| Xmax | 3 mm |
| Re | 13.5 Ω |
| Bl | 15.1 T·m |
| Mms | 67 g |
| Pe | 60 W |
| Sensitivity | 87.8 dB |
Alignment hint
| EBP | 40 · sealed |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | Qts too high |
EBP < 50: favours a sealed (closed) alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| Goldwood GW-1248 | 33.3 -3.1 | 0.933 +0.12 | 103.6 -18.7 | 3 = | 87.2 -0.6 | close | 8 Ω vs 16 Ω: amp load changes | + |
| Infinity 1200WIB vp | 35 -1.4 | 0.789 -0.03 | 116 -6.3 | 5.1 +2.1 | 92.8 +5 | usable | 4 Ω vs 16 Ω: amp load changes | + |
| Visaton WS32AW vp de FREDO51 | 39 +2.6 | 0.765 -0.05 | 115 -7.3 | 5 +2 | 91.5 +3.7 | usable | 8 Ω vs 16 Ω: amp load changes | + |
| Pioneer PAX30G vp2 | 42.1 +5.7 | 0.879 +0.06 | 92.7 -29.6 | 3 = | 88.2 +0.4 | usable | + | |
| Kenford HW-1206 | 31 -5.4 | 0.8 -0.02 | 170 +47.7 | 3 = | 89.5 +1.7 | usable | 8 Ω vs 16 Ω: amp load changes | + |
| Lautsprecher Technik MHB-12 | 38.2 +1.8 | 1.107 +0.29 | 132.7 +10.4 | 5 +2 | 88.9 +1.1 | usable | 8 Ω vs 16 Ω: amp load changes | + |
| Cabasse 30BZ18 v2 | 38.5 +2.1 | 0.747 -0.07 | 154.7 +32.4 | 4 +1 | 92.8 +5 | usable | 8 Ω vs 16 Ω: amp load changes | + |
| Fane SOVEREIGN 12-125 | 47 +10.6 | 0.796 -0.02 | 113.2 -9.1 | 4.9 +1.9 | 93.8 +6 | usable | 8 Ω vs 16 Ω: amp load changes | + |
| Samy Speaker LW1200 v1 | 27.1 -9.3 | 0.754 -0.06 | 159.6 +37.3 | 4.5 +1.5 | 87 -0.8 | usable | + | |
| Sony XS-NW1201 | 27.5 -8.9 | 0.928 +0.11 | 151.21 +28.91 | 4.15 +1.15 | 86.7 -1.1 | usable | 4 Ω vs 16 Ω: amp load changes | + |
Compare the closest 3 against the PAX30G vp1 →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.