PHL Audio 6051
Thiele-Small parameters
| Nominal size | 15" |
|---|---|
| Impedance | 8 Ω |
| Fs | 39 Hz |
| Qts | 0.209 |
| Qes | 0.22 |
| Qms | 4.21 |
| Vas | 135.6 L |
| Sd | 892 cm² |
| Xmax | 5.3 mm |
| Re | 4.1 Ω |
| Bl | 25 T·m |
| Mms | 137 g |
| Pe | 700 W |
| Sensitivity | 100.5 dB |
Alignment hint
| EBP | 177 · ported |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 13 L |
EBP > 100: favours a ported (bass-reflex) alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| PHL Audio 6050 | 40 +1 | 0.209 = | 130 -5.6 | 5.1 -0.2 | 100.7 +0.2 | close | Xmax 5.1 mm < 5.3 mm: lower excursion-limited SPL | + |
| B&C 15FW76 | 40 +1 | 0.21 = | 138 +2.4 | 7 +1.7 | 100 -0.5 | close | 500 W vs 700 W: lower power handling | + |
| B&C 15 FW 76 | 40 +1 | 0.211 = | 138 +2.4 | 4.7 -0.6 | 100.1 -0.4 | close | 500 W vs 700 W: lower power handling · Xmax 4.7 mm < 5.3 mm: lower excursion-limited SPL | + |
| Oberton 15LX600 | 40.9 +1.9 | 0.216 +0.01 | 150.3 +14.7 | 5.3 = | 100.4 -0.1 | close | + | |
| B&C 15NW76 | 39 = | 0.21 = | 143 +7.4 | 8 +2.7 | 99 -1.5 | close | 4 Ω vs 8 Ω: amp load changes | + |
| RCF MB 15N401 | 42 +3 | 0.195 -0.01 | 136 +0.4 | 5.3 = | 101 +0.5 | close | + | |
| Oberton 15XL601 | 40.9 +1.9 | 0.216 +0.01 | 150.32 +14.72 | 5.25 -0.05 | 100 -0.5 | close | Xmax 5.25 mm < 5.3 mm: lower excursion-limited SPL | + |
| Precision Devices PD154 | 39 = | 0.205 = | 149 +13.4 | 6.5 +1.2 | 99 -1.5 | close | 16 Ω vs 8 Ω: amp load changes · 500 W vs 700 W: lower power handling | + |
| B&C 15 NW 76 | 42 +3 | 0.218 +0.01 | 130 -5.6 | 4.9 -0.4 | 100 -0.5 | close | Xmax 4.9 mm < 5.3 mm: lower excursion-limited SPL | + |
| B&C 15NW76 | 42 +3 | 0.22 +0.01 | 130 -5.6 | 8 +2.7 | 100.5 = | close | + |
Compare the closest 3 against the 6051 →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.