Peerless SLS12 830669
Thiele-Small parameters
| Nominal size | 12" |
|---|---|
| Impedance | 8 Ω |
| Fs | 28 Hz |
| Qts | 0.474 |
| Qes | 0.51 |
| Qms | 6.7 |
| Vas | 172.4 L |
| Sd | 540 cm² |
| Xmax | 6.8 mm |
| Re | 5.7 Ω |
| Bl | 12.3 T·m |
| Mms | 76.6 g |
| Pe | 100 W |
| Sensitivity | 92.2 dB |
Alignment hint
| EBP | 55 · flexible |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 140.7 L |
EBP 50-100: works in either a sealed or ported alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| Infinity KAPPA CS 120 LB | 29 +1 | 0.485 +0.01 | 161.4 -11 | 6.7 -0.1 | 94.3 +2.1 | close | 4 Ω vs 8 Ω: amp load changes · Xmax 6.7 mm < 6.8 mm: lower excursion-limited SPL | + |
| HiVi W12 | 28 = | 0.419 -0.05 | 156 -16.4 | 6.9 +0.1 | 91.1 -1.1 | close | + | |
| Monacor SPH-300KE vp2 | 27.6 -0.4 | 0.489 +0.02 | 139.3 -33.1 | 6.5 -0.3 | 90.4 -1.8 | close | Xmax 6.5 mm < 6.8 mm: lower excursion-limited SPL | + |
| Visaton W300-8 | 32 +4 | 0.449 -0.02 | 190 +17.6 | 7 +0.2 | 93.4 +1.2 | close | + | |
| Philips AD12100W8 vp doum1 | 29.9 +1.9 | 0.413 -0.06 | 166 -6.4 | 6 -0.8 | 92.5 +0.3 | close | Xmax 6 mm < 6.8 mm: lower excursion-limited SPL | + |
| Philips AD12100W8 vp doum2 | 29.3 +1.3 | 0.399 -0.07 | 165 -7.4 | 6 -0.8 | 92.5 +0.3 | close | Xmax 6 mm < 6.8 mm: lower excursion-limited SPL | + |
| Beyma 12"BR70 | 31 +3 | 0.5 +0.03 | 142 -30.4 | 8 +1.2 | 93 +0.8 | close | + | |
| Peerless SLS315 | 24.4 -3.6 | 0.452 -0.02 | 205.2 +32.8 | 7.8 +1 | 91.4 -0.8 | close | + | |
| Visaton W300 | 32 +4 | 0.549 +0.08 | 190 +17.6 | 7 +0.2 | 92.2 = | close | + | |
| Beyma 12BR70 v2014 | 31 +3 | 0.497 +0.02 | 142 -30.4 | 6 -0.8 | 92.3 +0.1 | close | Xmax 6 mm < 6.8 mm: lower excursion-limited SPL | + |
Compare the closest 3 against the SLS12 830669 →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.