Precision Devices PD158
Thiele-Small parameters
| Nominal size | 15" |
|---|---|
| Impedance | 8 Ω |
| Fs | 39.85 Hz |
| Qts | 0.205 |
| Qes | 0.215 |
| Qms | 6.935 |
| Vas | 161.94 L |
| Sd | 881.41 cm² |
| Xmax | 6.5 mm |
| Bl | 27.35 T·m |
| Mms | 107.905 g |
| Pe | 600 W |
| Sensitivity | 98.5 dB |
Alignment hint
| EBP | 185 · ported |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 14.9 L |
EBP > 100: favours a ported (bass-reflex) alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| Precision Devices PD154 | 39 -0.85 | 0.205 = | 149 -12.94 | 6.5 = | 99 +0.5 | close | 16 Ω vs 8 Ω: amp load changes | + |
| Precision Devices PD153 ER | 39 -0.85 | 0.222 +0.02 | 160 -1.94 | 6.5 = | 99 +0.5 | close | 16 Ω vs 8 Ω: amp load changes · 400 W vs 600 W: lower power handling | + |
| B&C 15NW76 | 39 -0.85 | 0.21 +0.01 | 143 -18.94 | 8 +1.5 | 99 +0.5 | close | 4 Ω vs 8 Ω: amp load changes | + |
| B&C 15 PL 100 | 37 -2.85 | 0.204 = | 152.9 -9.04 | 6 -0.5 | 99.4 +0.9 | close | Xmax 6 mm < 6.5 mm: lower excursion-limited SPL | + |
| B&C 15FW76 | 40 +0.15 | 0.21 +0.01 | 138 -23.94 | 7 +0.5 | 100 +1.5 | close | + | |
| PHL Audio 6321MND | 34 -5.85 | 0.207 = | 150 -11.94 | 7.2 +0.7 | 98.1 -0.4 | close | + | |
| RCF LF 15N401 | 34 -5.85 | 0.221 +0.02 | 160 -1.94 | 7.1 +0.6 | 98.3 -0.2 | close | + | |
| Beyma 15"P80Nd | 39 -0.85 | 0.21 +0.01 | 184 +22.06 | 7.5 +1 | 101 +2.5 | close | + | |
| PD PD 158 | 39.9 +0.05 | 0.241 +0.04 | 161.9 -0.04 | 5.9 -0.6 | 99.4 +0.9 | close | Xmax 5.9 mm < 6.5 mm: lower excursion-limited SPL | + |
| Precision Devices PD 158 | 39.9 +0.05 | 0.241 +0.04 | 161.9 -0.04 | 5.9 -0.6 | 99.4 +0.9 | close | Xmax 5.9 mm < 6.5 mm: lower excursion-limited SPL | + |
Compare the closest 3 against the PD158 →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.