Precision Devices PD.185N02
Thiele-Small parameters
| Nominal size | 18" |
|---|---|
| Impedance | 8 Ω |
| Fs | 35.2 Hz |
| Qts | 0.24 |
| Qes | 0.25 |
| Qms | 22.1 |
| Vas | 178.28 L |
| Sd | 1182 cm² |
| Xmax | 12 mm |
| Re | 4.7 Ω |
| Bl | 30.6 T·m |
| Mms | 219.9 g |
| Pe | 1100 W |
| Sensitivity | 96.8 dB |
Alignment hint
| EBP | 141 · ported |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 23.2 L |
EBP > 100: favours a ported (bass-reflex) alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| Precision Devices PD.1850/2 | 33.1 -2.1 | 0.24 = | 203.84 +25.56 | 11.1 -0.9 | 96.7 -0.1 | close | 800 W vs 1100 W: lower power handling · Xmax 11.1 mm < 12 mm: lower excursion-limited SPL | + |
| Beyma 18QLEX1600Fe | 31 -4.2 | 0.25 +0.01 | 177.2 -1.08 | 13 +1 | 96 -0.8 | close | 4 Ω vs 8 Ω: amp load changes | + |
| B&C 18DS100 | 32 -3.2 | 0.24 = | 157 -21.28 | 14 +2 | 98 +1.2 | close | 4 Ω vs 8 Ω: amp load changes | + |
| Beyma 18QLEX1600Fe | 30 -5.2 | 0.23 -0.01 | 195 +16.72 | 13 +1 | 97 +0.2 | close | + | |
| Precision Devices PD.185C003-8 | 33 -2.2 | 0.24 = | 224 +45.72 | 11 -1 | 97.3 +0.5 | close | Xmax 11 mm < 12 mm: lower excursion-limited SPL | + |
| Oberton 18XB1301DS | 35.7 +0.5 | 0.302 +0.06 | 172.9 -5.38 | 12 = | 97.5 +0.7 | close | + | |
| Fane COLOSSUS 18-1500 | 33.5 -1.7 | 0.25 +0.01 | 175 -3.28 | 8.1 -3.9 | 97.8 +1 | close | Xmax 8.1 mm < 12 mm: lower excursion-limited SPL | + |
| Oberton 18NXB1600 | 32.37 -2.83 | 0.303 +0.06 | 173.11 -5.17 | 13.5 +1.5 | 97 +0.2 | close | + | |
| 18 Sound 18LW2600 | 30 -5.2 | 0.28 +0.04 | 186 +7.72 | 14 +2 | 96.5 -0.3 | close | 4 Ω vs 8 Ω: amp load changes | + |
| 18 Sound 18LW2600 | 31 -4.2 | 0.29 +0.05 | 187 +8.72 | 14.8 +2.8 | 96.8 = | usable | + |
Compare the closest 3 against the PD.185N02 →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.