Precision Devices PD.185C003-8
Thiele-Small parameters
| Nominal size | 18" |
|---|---|
| Impedance | 8 Ω |
| Fs | 33 Hz |
| Qts | 0.24 |
| Qes | 0.229 |
| Qms | 10.6 |
| Vas | 224 L |
| Sd | 1164 cm² |
| Xmax | 11 mm |
| Re | 5.4 Ω |
| Bl | 31.5 T·m |
| Mms | 197 g |
| Pe | 1000 W |
| Sensitivity | 97.3 dB |
Alignment hint
| EBP | 144 · ported |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 29.2 L |
EBP > 100: favours a ported (bass-reflex) alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| Precision Devices PD.1850/2 | 33.1 +0.1 | 0.24 = | 203.84 -20.16 | 11.1 +0.1 | 96.7 -0.6 | close | + | |
| RCF LF18N451 | 31 -2 | 0.24 = | 245 +21 | 9 -2 | 97.5 +0.2 | close | Xmax 9 mm < 11 mm: lower excursion-limited SPL | + |
| Beyma 18PW1400FE /S | 32 -1 | 0.27 +0.03 | 228.9 +4.9 | 10 -1 | 98 +0.7 | close | Xmax 10 mm < 11 mm: lower excursion-limited SPL | + |
| Precision Devices PD.185N02 | 35.2 +2.2 | 0.24 = | 178.28 -45.72 | 12 +1 | 96.8 -0.5 | close | + | |
| Beyma 18QLEX1600Fe | 30 -3 | 0.23 -0.01 | 195 -29 | 13 +2 | 97 -0.3 | close | + | |
| PD PD 185C003 | 33 = | 0.224 -0.02 | 224 = | 8.8 -2.2 | 99.1 +1.8 | close | Xmax 8.8 mm < 11 mm: lower excursion-limited SPL | + |
| Precision Devices PD 185C003 | 33 = | 0.224 -0.02 | 224 = | 8.8 -2.2 | 99.1 +1.8 | close | Xmax 8.8 mm < 11 mm: lower excursion-limited SPL | + |
| 18 Sound 18NLW9000 | 32 -1 | 0.21 -0.03 | 247 +23 | 14 +3 | 97 -0.3 | close | 4 Ω vs 8 Ω: amp load changes | + |
| RCF LF 18X451 | 30 -3 | 0.278 +0.04 | 220 -4 | 10.7 -0.3 | 96.8 -0.5 | close | Xmax 10.7 mm < 11 mm: lower excursion-limited SPL | + |
| RCF LF 18N451 | 31 -2 | 0.24 = | 245 +21 | 8.8 -2.2 | 98.7 +1.4 | close | Xmax 8.8 mm < 11 mm: lower excursion-limited SPL | + |
Compare the closest 3 against the PD.185C003-8 →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.