PD PD 1845-1N
Thiele-Small parameters
| Nominal size | 18" |
|---|---|
| Impedance | 8 Ω |
| Fs | 34.1 Hz |
| Qts | 0.323 |
| Qes | 0.333 |
| Qms | 10.961 |
| Vas | 176 L |
| Sd | 1158.1 cm² |
| Xmax | 9.5 mm |
| Re | 4.7 Ω |
| Bl | 26.5 T·m |
| Mms | 232.7 g |
| Pe | 1500 W |
| Sensitivity | 97.5 dB |
Alignment hint
| EBP | 102 · ported |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 46.4 L |
EBP > 100: favours a ported (bass-reflex) alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| Precision Devices PD 1845-1N | 34.1 = | 0.323 = | 176 = | 9.5 = | 97.5 = | close | + | |
| Faital PRO 18HP1030 | 35 +0.9 | 0.32 = | 172.2 -3.8 | 12.45 +2.95 | 98 +0.5 | close | 4 Ω vs 8 Ω: amp load changes | + |
| Faital PRO 18HP1060 | 35 +0.9 | 0.33 +0.01 | 184.4 +8.4 | 12.45 +2.95 | 98 +0.5 | close | 4 Ω vs 8 Ω: amp load changes | + |
| B&C 18TBW100 | 33 -1.1 | 0.32 = | 181.5 +5.5 | 12 +2.5 | 96 -1.5 | close | 4 Ω vs 8 Ω: amp load changes | + |
| Oberton 18XB1301DS | 35.7 +1.6 | 0.302 -0.02 | 172.9 -3.1 | 12 +2.5 | 97.5 = | close | + | |
| LaVoce SAF184.50 | 35 +0.9 | 0.329 +0.01 | 162 -14 | 9.2 -0.3 | 96.5 -1 | close | Xmax 9.2 mm < 9.5 mm: lower excursion-limited SPL | + |
| Fane COLOSSUS 18XT5N | 36 +1.9 | 0.331 +0.01 | 185 +9 | 8.4 -1.1 | 97.4 -0.1 | close | Xmax 8.4 mm < 9.5 mm: lower excursion-limited SPL | + |
| 18 Sound 18LW2420 | 34 -0.1 | 0.31 -0.01 | 208 +32 | 10 +0.5 | 98 +0.5 | close | 4 Ω vs 8 Ω: amp load changes | + |
| Oberton 18XB700 | 36.1 +2 | 0.304 -0.02 | 183.22 +7.22 | 9 -0.5 | 98 +0.5 | close | 1000 W vs 1500 W: lower power handling · Xmax 9 mm < 9.5 mm: lower excursion-limited SPL | + |
| Oberton 18NXB1600 | 32.37 -1.73 | 0.303 -0.02 | 173.11 -2.89 | 13.5 +4 | 97 -0.5 | close | + |
Compare the closest 3 against the PD 1845-1N →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.