Precision Devices PD.153C01
Thiele-Small parameters
| Nominal size | 15" |
|---|---|
| Impedance | 8 Ω |
| Fs | 39 Hz |
| Qts | 0.27 |
| Qes | 0.276 |
| Qms | 13.1 |
| Vas | 195 L |
| Sd | 899 cm² |
| Xmax | 5.7 mm |
| Re | 5.2 Ω |
| Bl | 21.7 T·m |
| Mms | 100 g |
| Pe | 400 W |
| Sensitivity | 98.1 dB |
Alignment hint
| EBP | 141 · ported |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 33.3 L |
EBP > 100: favours a ported (bass-reflex) alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| Eminence PS15-5008 | 38.8 -0.2 | 0.273 = | 198.7 +3.7 | 6.3 +0.6 | 99.8 +1.7 | close | + | |
| PD PD 153 C01 | 39 = | 0.265 -0.01 | 195 = | 5.5 -0.2 | 100.2 +2.1 | close | Xmax 5.5 mm < 5.7 mm: lower excursion-limited SPL | + |
| Precision Devices PD 153 C01 | 39 = | 0.265 -0.01 | 195 = | 5.5 -0.2 | 100.2 +2.1 | close | Xmax 5.5 mm < 5.7 mm: lower excursion-limited SPL | + |
| Audax PR38ST350 | 36 -3 | 0.28 +0.01 | 193 -2 | 5.5 -0.2 | 98.3 +0.2 | close | Xmax 5.5 mm < 5.7 mm: lower excursion-limited SPL | + |
| Audax PR38XT350 | 36 -3 | 0.28 +0.01 | 193 -2 | 5.5 -0.2 | 98.3 +0.2 | close | Xmax 5.5 mm < 5.7 mm: lower excursion-limited SPL | + |
| Audax LFP504 | 36 -3 | 0.282 +0.01 | 193 -2 | 5.5 -0.2 | 98.2 +0.1 | close | Xmax 5.5 mm < 5.7 mm: lower excursion-limited SPL | + |
| 18 Sound 15W700 | 41 +2 | 0.27 = | 180 -15 | 6.5 +0.8 | 97 -1.1 | close | 4 Ω vs 8 Ω: amp load changes | + |
| PHL Audio 5012MNdU | 36 -3 | 0.268 = | 175 -20 | 6 +0.3 | 98.3 +0.2 | close | + | |
| PHL Audio 5011 | 36 -3 | 0.268 = | 174.7 -20.3 | 6 +0.3 | 98.3 +0.2 | close | + | |
| Radian 5215B v2017 | 40 +1 | 0.266 = | 202 +7 | 5.5 -0.2 | 100.3 +2.2 | close | Xmax 5.5 mm < 5.7 mm: lower excursion-limited SPL | + |
Compare the closest 3 against the PD.153C01 →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.