Monacor SPH-200TC bobines en série

12" · 16 Ω · 60 W · 87.3 dB

Thiele-Small parameters

Nominal size	12"
Impedance	16 Ω
Fs	28 Hz
Qts	0.239
Qes	0.249
Qms	6.19
Vas	65 L
Sd	420 cm²
Xmax	2.9 mm
Re	13.6 Ω
Bl	34.4 T·m
Mms	122.9 g
Pe	60 W
Sensitivity	87.3 dB

Alignment hint

EBP	112 · ported
Sealed Vb (Qtc ≈ 0.71)	≈ 8.4 L

EBP > 100: favours a ported (bass-reflex) alignment.

Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.

Substitute candidates

Driver	Fs (Hz)	Qts	Vas (L)	Xmax (mm)	Sens (dB)	Fit	Notes	Compare
Helix P12W PRECISION	27 -1	0.25 +0.01	72 +7	8.5 +5.6	89 +1.7	close	4 Ω vs 16 Ω: amp load changes	+
Mivoc AWM 124	30 +2	0.251 +0.01	68 +3	4.7 +1.8	94.6 +7.3	usable	4 Ω vs 16 Ω: amp load changes	+
Alcone AC 12 SW-8	25.7 -2.3	0.224 -0.01	84.4 +19.4	4 +1.1	90.9 +3.6	usable	8 Ω vs 16 Ω: amp load changes	+
BMS 12S330 v2016	28.6 +0.6	0.24 =	85.5 +20.5	8 +5.1	92.3 +5	usable	8 Ω vs 16 Ω: amp load changes	+
Celestion FTR12-4080DL	28.9 +0.9	0.303 +0.06	68.6 +3.6	8.7 +5.8	89.9 +2.6	usable	8 Ω vs 16 Ω: amp load changes	+
Artech SPM-303	30 +2	0.243 =	95 +30	3.6 +0.7	92.3 +5	usable	8 Ω vs 16 Ω: amp load changes	+
Raveland BSW 124-II	28 =	0.252 +0.01	91.4 +26.4	5.4 +2.5	94.7 +7.4	usable	4 Ω vs 16 Ω: amp load changes	+
BMS 12S330 v2018	28.6 +0.6	0.295 +0.06	81.4 +16.4	8 +5.1	91.1 +3.8	usable	8 Ω vs 16 Ω: amp load changes	+
BMS 12S330	28.6 +0.6	0.24 =	85.5 +20.5	8 +5.1	96 +8.7	usable	8 Ω vs 16 Ω: amp load changes	+
HiVi M12 8 Ohms	27 -1	0.335 +0.1	81.4 +16.4	5.2 +2.3	89.4 +2.1	usable	8 Ω vs 16 Ω: amp load changes	+

Compare the closest 3 against the SPH-200TC bobines en série →

Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.

Used in enclosures (0)

No enclosure in the catalog uses this driver yet.