Monacor SP-300PA
Thiele-Small parameters
| Nominal size | 12" |
|---|---|
| Impedance | 8 Ω |
| Fs | 40 Hz |
| Qts | 0.435 |
| Qes | 0.52 |
| Qms | 2.65 |
| Vas | 150 L |
| Sd | 514 cm² |
| Xmax | 3.3 mm |
| Re | 6.9 Ω |
| Bl | 11.4 T·m |
| Mms | 39.1 g |
| Pe | 175 W |
| Sensitivity | 95.3 dB |
Alignment hint
| EBP | 77 · flexible |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 91.3 L |
EBP 50-100: works in either a sealed or ported alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| Klipsch K28E | 35.1 -4.9 | 0.441 +0.01 | 152.7 +2.7 | 4 +0.7 | 96.5 +1.2 | close | 4 Ω vs 8 Ω: amp load changes · 100 W vs 175 W: lower power handling | + |
| Tannoy 3149R | 38 -2 | 0.436 = | 138 -12 | 2.6 -0.7 | 95.2 -0.1 | close | 80 W vs 175 W: lower power handling · Xmax 2.6 mm < 3.3 mm: lower excursion-limited SPL | + |
| LaVoce LBASS12-15 | 38 -2 | 0.48 +0.04 | 160.93 +10.93 | 4.7 +1.4 | 95.5 +0.2 | close | 100 W vs 175 W: lower power handling | + |
| Conrad PA 12 | 42.9 +2.9 | 0.462 +0.03 | 129.2 -20.8 | 4 +0.7 | 95.2 -0.1 | close | + | |
| Hyper Phase CM12 | 40 = | 0.372 -0.06 | 135 -15 | 3.5 +0.2 | 96.3 +1 | close | 100 W vs 175 W: lower power handling | + |
| Davis KIT ALBEDO | 37.5 -2.5 | 0.459 +0.02 | 166 +16 | 5 +1.7 | 96.5 +1.2 | close | + | |
| Philips AD12202/M8 | 45.6 +5.6 | 0.419 -0.02 | 138 -12 | 4 +0.7 | 96.8 +1.5 | close | 100 W vs 175 W: lower power handling | + |
| Eminence BETA 12CX | 43 +3 | 0.474 +0.04 | 161 +11 | 3.5 +0.2 | 97.5 +2.2 | close | + | |
| Eminence DELTALITE II 2512 v2 | 37 -3 | 0.386 -0.05 | 147 -3 | 4.9 +1.6 | 96.3 +1 | close | + | |
| Supravox 285 GMF vp5 | 35 -5 | 0.372 -0.06 | 150 = | 4 +0.7 | 95.4 +0.1 | close | 70 W vs 175 W: lower power handling | + |
Compare the closest 3 against the SP-300PA →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.