Jensen 15 LL _ 25V
Thiele-Small parameters
| Nominal size | 15" |
|---|---|
| Impedance | 16 Ω |
| Fs | 46.5 Hz |
| Qts | 0.201 |
| Qes | 0.206 |
| Qms | 8.296 |
| Vas | 154 L |
| Sd | 858.5 cm² |
| Xmax | 2.8 mm |
| Re | 10.5 Ω |
| Bl | 34.2 T·m |
| Mms | 78.5 g |
| Pe | 200 W |
| Sensitivity | 99.6 dB |
Alignment hint
| EBP | 226 · ported |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 13.5 L |
EBP > 100: favours a ported (bass-reflex) alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| PD PD 154 | 39 -7.5 | 0.206 = | 149 -5 | 4.6 +1.8 | 99.2 -0.4 | close | 8 Ω vs 16 Ω: amp load changes | + |
| Precision Devices PD 154 | 39 -7.5 | 0.206 = | 149 -5 | 4.6 +1.8 | 99.2 -0.4 | close | 8 Ω vs 16 Ω: amp load changes | + |
| Oberton 15XL601 | 40.9 -5.6 | 0.216 +0.01 | 150.32 -3.68 | 5.25 +2.45 | 100 +0.4 | close | 8 Ω vs 16 Ω: amp load changes | + |
| Oberton 15LX600 | 40.9 -5.6 | 0.216 +0.01 | 150.3 -3.7 | 5.3 +2.5 | 100.4 +0.8 | close | 8 Ω vs 16 Ω: amp load changes | + |
| B&C 15 PL 100 | 37 -9.5 | 0.204 = | 152.9 -1.1 | 6 +3.2 | 99.4 -0.2 | close | 8 Ω vs 16 Ω: amp load changes | + |
| Precision Devices PD154 | 39 -7.5 | 0.205 = | 149 -5 | 6.5 +3.7 | 99 -0.6 | close | + | |
| PD PD 153ER | 39 -7.5 | 0.219 +0.02 | 160 +6 | 4.8 +2 | 99.6 = | close | 8 Ω vs 16 Ω: amp load changes | + |
| Precision Devices PD 153ER | 39 -7.5 | 0.219 +0.02 | 160 +6 | 4.8 +2 | 99.6 = | close | 8 Ω vs 16 Ω: amp load changes | + |
| Precision Devices PD158 | 39.85 -6.65 | 0.205 = | 161.94 +7.94 | 6.5 +3.7 | 98.5 -1.1 | close | 8 Ω vs 16 Ω: amp load changes | + |
| B&C 15 FW 76 | 40 -6.5 | 0.211 +0.01 | 138 -16 | 4.7 +1.9 | 100.1 +0.5 | close | 8 Ω vs 16 Ω: amp load changes | + |
Compare the closest 3 against the 15 LL _ 25V →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.