Isophon PSL 300/50
Thiele-Small parameters
| Nominal size | 12" |
|---|---|
| Impedance | 4 Ω |
| Fs | 40.3 Hz |
| Qts | 0.582 |
| Qes | 0.672 |
| Qms | 4.367 |
| Vas | 71.7 L |
| Sd | 518.7 cm² |
| Xmax | 2.8 mm |
| Re | 2.7 Ω |
| Bl | 9.1 T·m |
| Mms | 82 g |
| Pe | 50 W |
| Sensitivity | 95.1 dB |
Alignment hint
| EBP | 60 · flexible |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 150.6 L |
EBP 50-100: works in either a sealed or ported alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| Pioneer TS-W1RS | 40.2 -0.1 | 0.516 -0.07 | 75.5 +3.8 | 4.2 +1.4 | 95.5 +0.4 | close | + | |
| Audax HT300G0 | 36.8 -3.5 | 0.531 -0.05 | 77.7 +6 | 6.6 +3.8 | 94.4 -0.7 | usable | + | |
| Supravox T285HF64 | 55 +14.7 | 0.6 +0.02 | 74.6 +2.9 | 3.3 +0.5 | 95.6 +0.5 | usable | 8 Ω vs 4 Ω: amp load changes | + |
| Siare 31TE vp 1 | 43.8 +3.5 | 0.545 -0.04 | 91.5 +19.8 | 4.5 +1.7 | 95.5 +0.4 | usable | 8 Ω vs 4 Ω: amp load changes | + |
| Skytronic 902.436 | 42 +1.7 | 0.6 +0.02 | 65 -6.7 | 4 +1.2 | 89.8 -5.3 | usable | 8 Ω vs 4 Ω: amp load changes | + |
| Elder Audio 12LB075-UMOD | 40 -0.3 | 0.472 -0.11 | 73 +1.3 | 5.5 +2.7 | 93.1 -2 | usable | 8 Ω vs 4 Ω: amp load changes | + |
| Dayton Audio 310-8 | 44.4 +4.1 | 0.482 -0.1 | 81.9 +10.2 | 3.5 +0.7 | 94.9 -0.2 | usable | 8 Ω vs 4 Ω: amp load changes | + |
| B&C 12 CLX 64 | 54 +13.7 | 0.575 -0.01 | 74 +2.3 | 5.3 +2.5 | 96.3 +1.2 | usable | 8 Ω vs 4 Ω: amp load changes | + |
| Conrad CPA 15-300 | 43 +2.7 | 0.559 -0.02 | 100.5 +28.8 | 4 +1.2 | 93.8 -1.3 | usable | 8 Ω vs 4 Ω: amp load changes | + |
| Monacor CRB-12TC vp parallèle | 31 -9.3 | 0.611 +0.03 | 75 +3.3 | 4.9 +2.1 | 93.5 -1.6 | usable | 2 Ω vs 4 Ω: amp load changes | + |
Compare the closest 3 against the PSL 300/50 →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.