Helix W-12 COMPETITION
Thiele-Small parameters
| Nominal size | 12" |
|---|---|
| Impedance | 4 Ω |
| Fs | 21.4 Hz |
| Qts | 0.3 |
| Qes | 0.33 |
| Qms | 3.6 |
| Vas | 118.6 L |
| Sd | 519 cm² |
| Xmax | 11 mm |
| Re | 3.2 Ω |
| Bl | 15.1 T·m |
| Mms | 174.9 g |
| Pe | 350 W |
| Sensitivity | 87.3 dB |
Alignment hint
| EBP | 65 · flexible |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 26 L |
EBP 50-100: works in either a sealed or ported alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| Kenwood XR-W1204 | 21.5 +0.1 | 0.341 +0.04 | 125.386 +6.79 | 10.8 -0.2 | 87.3 = | close | Xmax 10.8 mm < 11 mm: lower excursion-limited SPL | + |
| Helix P12 | 21.4 = | 0.302 = | 118.6 = | 9.9 -1.1 | 91.4 +4.1 | close | Xmax 9.9 mm < 11 mm: lower excursion-limited SPL | + |
| Visaton TIW 360X | 21 -0.4 | 0.34 +0.04 | 140 +21.4 | 12.5 +1.5 | 87.3 = | close | 8 Ω vs 4 Ω: amp load changes | + |
| Eminence LAB 12C | 23 +1.6 | 0.33 +0.03 | 128.31 +9.71 | 13 +2 | 88.9 +1.6 | close | + | |
| Visaton TIW360X | 21 -0.4 | 0.336 +0.04 | 140 +21.4 | 12.2 +1.2 | 88.8 +1.5 | close | 8 Ω vs 4 Ω: amp load changes | + |
| Pioneer TS-W 304 C | 21 -0.4 | 0.307 +0.01 | 136 +17.4 | 11 = | 92.2 +4.9 | close | + | |
| Pioneer TS-W1201C | 20 -1.4 | 0.291 -0.01 | 118 -0.6 | 9.2 -1.8 | 91.2 +3.9 | close | Xmax 9.2 mm < 11 mm: lower excursion-limited SPL | + |
| Ground Zero GZHW 30X | 22.6 +1.2 | 0.32 +0.02 | 101 -17.6 | 12.3 +1.3 | 90.6 +3.3 | usable | + | |
| Eminence LAB 12 | | 22 +0.6 | 0.38 +0.08 | 125.2 +6.6 | 13 +2 | 89.2 +1.9 | usable | 6 Ω vs 4 Ω: amp load changes | + |
| Eminence LAB 12 | 22 +0.6 | 0.379 +0.08 | 125.2 +6.6 | 11 = | 90 +2.7 | usable | 8 Ω vs 4 Ω: amp load changes | + |
Compare the closest 3 against the W-12 COMPETITION →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.