Fenton NS10X
Thiele-Small parameters
| Nominal size | 10" |
|---|---|
| Impedance | 8 Ω |
| Fs | 67.5 Hz |
| Qts | 0.563 |
| Qes | 0.65 |
| Qms | 4.185 |
| Vas | 40.2 L |
| Sd | 339.8 cm² |
| Xmax | 3.8 mm |
| Re | 6.6 Ω |
| Bl | 9.8 T·m |
| Mms | 22.4 g |
| Pe | 125 W |
| Sensitivity | 95.6 dB |
Alignment hint
| EBP | 104 · ported |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 69.6 L |
EBP > 100: favours a ported (bass-reflex) alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| Beyma CM-10 | 61 -6.5 | 0.506 -0.06 | 40.7 +0.5 | 3.6 -0.2 | 95.4 -0.2 | close | Xmax 3.6 mm < 3.8 mm: lower excursion-limited SPL | + |
| Fenton PS10F vp | 60.1 -7.4 | 0.586 +0.02 | 41.2 +1 | 4 +0.2 | 93.3 -2.3 | close | 16 Ω vs 8 Ω: amp load changes | + |
| Hyper Phase CM10 | 65 -2.5 | 0.511 -0.05 | 45 +4.8 | 3.3 -0.5 | 95.6 = | close | Xmax 3.3 mm < 3.8 mm: lower excursion-limited SPL | + |
| Celestion K10-200E | 67 -0.5 | 0.471 -0.09 | 37 -3.2 | 4 +0.2 | 97.3 +1.7 | close | + | |
| Celestion BL 10-100 | 70 +2.5 | 0.608 +0.05 | 33 -7.2 | 3.3 -0.5 | 95.7 +0.1 | close | Xmax 3.3 mm < 3.8 mm: lower excursion-limited SPL | + |
| Beyma PRO CM10 | 60 -7.5 | 0.594 +0.03 | 49.6 +9.4 | 4.2 +0.4 | 95.3 -0.3 | close | + | |
| LaVoce FBASS10-18-16 | 70 +2.5 | 0.57 +0.01 | 28.39 -11.81 | 4.8 +1 | 95 -0.6 | close | 16 Ω vs 8 Ω: amp load changes | + |
| Monacor SPA-110PA | 61 -6.5 | 0.469 -0.09 | 38 -2.2 | 4 +0.2 | 96.3 +0.7 | close | + | |
| Siemens C 71233-4A-A1 | 70.2 +2.7 | 0.546 -0.02 | 58.6 +18.4 | 4 +0.2 | 95.1 -0.5 | close | 16 Ω vs 8 Ω: amp load changes · 80 W vs 125 W: lower power handling | + |
| Radian CRS1030 | 65 -2.5 | 0.472 -0.09 | 35.3 -4.9 | 5.5 +1.7 | 96.2 +0.6 | usable | + |
Compare the closest 3 against the NS10X →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.