Fane SOVEREIGN 12-300 v2014
Thiele-Small parameters
| Nominal size | 12" |
|---|---|
| Impedance | 8 Ω |
| Fs | 46 Hz |
| Qts | 0.35 |
| Qes | 0.375 |
| Qms | 5.2 |
| Vas | 110 L |
| Sd | 530 cm² |
| Xmax | 4.5 mm |
| Re | 5.75 Ω |
| Bl | 13.8 T·m |
| Mms | 42.9 g |
| Pe | 300 W |
| Sensitivity | 98 dB |
Alignment hint
| EBP | 123 · ported |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 35.7 L |
EBP > 100: favours a ported (bass-reflex) alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| Fane SOVEREIGN PRO 12-300 | 46 = | 0.35 = | 114 +4 | 4.5 = | 98.1 +0.1 | close | + | |
| Fane SOVEREIGN PRO 12-350N | 46 = | 0.328 -0.02 | 114 +4 | 4.5 = | 98.4 +0.4 | close | + | |
| 18 Sound 12W500 | 49 +3 | 0.35 = | 101 -9 | 4 -0.5 | 98.5 +0.5 | close | 4 Ω vs 8 Ω: amp load changes · Xmax 4 mm < 4.5 mm: lower excursion-limited SPL | + |
| Monacor SP-12/200PA | 45 -1 | 0.328 -0.02 | 114 +4 | 4 -0.5 | 97.4 -0.6 | close | 200 W vs 300 W: lower power handling · Xmax 4 mm < 4.5 mm: lower excursion-limited SPL | + |
| 18 Sound 12W501 | 46 = | 0.369 +0.02 | 123 +13 | 4 -0.5 | 98.7 +0.7 | close | Xmax 4 mm < 4.5 mm: lower excursion-limited SPL | + |
| Beyma 12LW30 | 45 -1 | 0.404 +0.05 | 110 = | 5 +0.5 | 97 -1 | close | + | |
| 18 Sound 12W500 | 46 = | 0.36 +0.01 | 123 +13 | 4 -0.5 | 99.5 +1.5 | close | Xmax 4 mm < 4.5 mm: lower excursion-limited SPL | + |
| Beyma 12XM | 42 -4 | 0.348 = | 125 +15 | 4 -0.5 | 97.9 -0.1 | close | Xmax 4 mm < 4.5 mm: lower excursion-limited SPL | + |
| Fane SOVEREIGN 12-300 | 50 +4 | 0.389 +0.04 | 103.6 -6.4 | 4.5 = | 98.4 +0.4 | close | + | |
| Fane SOVEREIGN PRO 12-500 | 43 -3 | 0.314 -0.04 | 107 -3 | 6 +1.5 | 97.4 -0.6 | close | + |
Compare the closest 3 against the SOVEREIGN 12-300 v2014 →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.