← all drivers

Fane COLOSSUS 12MBN

12" · 8 Ω · 500 W · 97.4 dB · datasheet ↗

Thiele-Small parameters

Nominal size12"
Impedance8 Ω
Fs55 Hz
Qts0.396
Qes0.438
Qms4.13
Vas63 L
Sd558.9 cm²
Xmax5.5 mm
Re5.5 Ω
Bl15.9 T·m
Mms58.2 g
Pe500 W
Sensitivity97.4 dB

Alignment hint

EBP126 · ported
Sealed Vb (Qtc ≈ 0.71)≈ 28.8 L

EBP > 100: favours a ported (bass-reflex) alignment.

Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.

Substitute candidates

DriverFs (Hz)QtsVas (L)Xmax (mm)Sens (dB)FitNotesCompare
Faital PRO 12HX50054 -10.396 =62.3 -0.75.5 =97.2 -0.2close+
Faital PRO 12PR310-854 -10.396 =62.8 -0.24.9 -0.697.5 +0.1close300 W vs 500 W: lower power handling · Xmax 4.9 mm < 5.5 mm: lower excursion-limited SPL+
SB Audience BIANCO-12MW20050 -50.389 -0.0168.7 +5.76 +0.597.2 -0.2close+
LaVoce WSN122.50-1653 -20.4 =65.84 +2.844.6 -0.996.5 -0.9close16 Ω vs 8 Ω: amp load changes · 250 W vs 500 W: lower power handling · Xmax 4.6 mm < 5.5 mm: lower excursion-limited SPL+
Beyma 12MC50057 +20.373 -0.0254.9 -8.15.5 =97.8 +0.4close+
Faital PRO 12PR300-450 -50.392 =63.1 +0.14.9 -0.698.8 +1.4close4 Ω vs 8 Ω: amp load changes · 300 W vs 500 W: lower power handling · Xmax 4.9 mm < 5.5 mm: lower excursion-limited SPL+
Beyma SM112 vp57.8 +2.80.391 -0.0164.6 +1.64.2 -1.397.7 +0.3close250 W vs 500 W: lower power handling · Xmax 4.2 mm < 5.5 mm: lower excursion-limited SPL+
Faital PRO 12PR300-854 -10.382 -0.0173.5 +10.54.9 -0.698.2 +0.8close300 W vs 500 W: lower power handling · Xmax 4.9 mm < 5.5 mm: lower excursion-limited SPL+
Faital PRO 12PR31054 -10.4 =73.5 +10.54.92 -0.5899 +1.6close300 W vs 500 W: lower power handling · Xmax 4.92 mm < 5.5 mm: lower excursion-limited SPL+
Radian 5212B62 +70.42 +0.0258.4 -4.65.4 -0.198.2 +0.8close375 W vs 500 W: lower power handling · Xmax 5.4 mm < 5.5 mm: lower excursion-limited SPL+

Compare the closest 3 against the COLOSSUS 12MBN →

Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.

Used in enclosures (0)

No enclosure in the catalog uses this driver yet.