← all drivers

Faital PRO 6RS140

6" · 8 Ω · 200 W · 93 dB · datasheet ↗

Thiele-Small parameters

Nominal size6"
Impedance8 Ω
Fs65 Hz
Qts0.27
Qes0.28
Qms5.8
Vas9.3 L
Sd133 cm²
Xmax5.6 mm
Re5.3 Ω
Mms16 g
Pe200 W
Sensitivity93 dB

Alignment hint

EBP232 · ported
Sealed Vb (Qtc ≈ 0.71)≈ 1.6 L

EBP > 100: favours a ported (bass-reflex) alignment.

Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.

Substitute candidates

DriverFs (Hz)QtsVas (L)Xmax (mm)Sens (dB)FitNotesCompare
LaVoce WAN061.8060 -50.27 =11.18 +1.885.2 -0.493 =closeXmax 5.2 mm < 5.6 mm: lower excursion-limited SPL+
LaVoce WAN061.80-1662 -30.31 +0.0410.26 +0.965.2 -0.492.5 -0.5close16 Ω vs 8 Ω: amp load changes · Xmax 5.2 mm < 5.6 mm: lower excursion-limited SPL+
Faital PRO 6RS14065 =0.36 +0.099.9 +0.65.5 -0.192 -1usable16 Ω vs 8 Ω: amp load changes · Xmax 5.5 mm < 5.6 mm: lower excursion-limited SPL+
Sica 6 NR 2 PL60.5 -4.50.33 +0.069.4 +0.14 -1.691.4 -1.6usableXmax 4 mm < 5.6 mm: lower excursion-limited SPL+
Sica 6 N 2 PL68 +30.33 +0.068.7 -0.63.5 -2.192.3 -0.7usableXmax 3.5 mm < 5.6 mm: lower excursion-limited SPL+
Sica 6 N 2.5 PL80 +150.27 =4.9 -4.44.5 -1.192.5 -0.5usableXmax 4.5 mm < 5.6 mm: lower excursion-limited SPL+
LaVoce WAF061.8065 =0.42 +0.157.26 -2.044.9 -0.791 -2usable150 W vs 200 W: lower power handling · Xmax 4.9 mm < 5.6 mm: lower excursion-limited SPL+
BMS 6S11780 +150.43 +0.1610.4 +1.15 -0.693 =usable16 Ω vs 8 Ω: amp load changes · 130 W vs 200 W: lower power handling · Xmax 5 mm < 5.6 mm: lower excursion-limited SPL+
Faital PRO 6PR16090 +250.33 +0.065.9 -3.45 -0.695 +2usable120 W vs 200 W: lower power handling · Xmax 5 mm < 5.6 mm: lower excursion-limited SPL+
BMS 6N16089 +240.47 +0.27.7 -1.65 -0.693 =risky16 Ω vs 8 Ω: amp load changes · 130 W vs 200 W: lower power handling · Xmax 5 mm < 5.6 mm: lower excursion-limited SPL+

Compare the closest 3 against the 6RS140 →

Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.

Used in enclosures (0)

No enclosure in the catalog uses this driver yet.