Faital PRO 5FE120
Thiele-Small parameters
| Nominal size | 5" |
|---|---|
| Impedance | 4 Ω |
| Fs | 65 Hz |
| Qts | 0.38 |
| Qes | 0.4 |
| Qms | 8.2 |
| Vas | 5 L |
| Sd | 79.8 cm² |
| Xmax | 5.2 mm |
| Re | 3.1 Ω |
| Mms | 10.9 g |
| Pe | 80 W |
| Sensitivity | 88 dB |
Alignment hint
| EBP | 163 · ported |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 2 L |
EBP > 100: favours a ported (bass-reflex) alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| Faital PRO 5FE100 | 65 = | 0.45 +0.07 | 5.7 +0.7 | 5.25 +0.05 | 88 = | close | 8 Ω vs 4 Ω: amp load changes | + |
| Faital PRO 5FE105 | 65 = | 0.45 +0.07 | 5.7 +0.7 | 5.25 +0.05 | 88 = | close | 8 Ω vs 4 Ω: amp load changes | + |
| Faital PRO 5FE120 | 65 = | 0.48 +0.1 | 5.4 +0.4 | 5.25 +0.05 | 88 = | close | 8 Ω vs 4 Ω: amp load changes | + |
| Faital PRO 5FE125 | 65 = | 0.48 +0.1 | 5.4 +0.4 | 5.25 +0.05 | 88 = | close | 8 Ω vs 4 Ω: amp load changes | + |
| Faital PRO 5FE100 | 65 = | 0.33 -0.05 | 6.1 +1.1 | 5.2 = | 87 -1 | close | + | |
| Beyma 5"MP60/N | 63 -2 | 0.46 +0.08 | 5.8 +0.8 | 5.5 +0.3 | 88 = | close | 8 Ω vs 4 Ω: amp load changes · 50 W vs 80 W: lower power handling | + |
| B&C 5FG44 | 70 +5 | 0.39 +0.01 | 5.1 +0.1 | 3 -2.2 | 90 +2 | usable | 16 Ω vs 4 Ω: amp load changes · Xmax 3 mm < 5.2 mm: lower excursion-limited SPL | + |
| Beyma 5P200Fe | 72 +7 | 0.33 -0.05 | 5.7 +0.7 | 5.7 +0.5 | 92 +4 | usable | 8 Ω vs 4 Ω: amp load changes | + |
| Faital PRO 5FE120 | 65 = | 0.51 +0.13 | 6.6 +1.6 | 5.25 +0.05 | 89 +1 | usable | 16 Ω vs 4 Ω: amp load changes | + |
| B&C 5NDL38 | 80 +15 | 0.36 -0.02 | 4.3 -0.7 | 3.5 -1.7 | 91 +3 | usable | 8 Ω vs 4 Ω: amp load changes · Xmax 3.5 mm < 5.2 mm: lower excursion-limited SPL | + |
Compare the closest 3 against the 5FE120 →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.