Faital PRO 4FE32
Thiele-Small parameters
| Nominal size | 4" |
|---|---|
| Impedance | 16 Ω |
| Fs | 100 Hz |
| Qts | 0.81 |
| Qes | 1.02 |
| Qms | 3.8 |
| Vas | 2.4 L |
| Sd | 51.9 cm² |
| Xmax | 1.83 mm |
| Re | 12.3 Ω |
| Mms | 4 g |
| Pe | 30 W |
| Sensitivity | 91 dB |
Alignment hint
| EBP | 98 · flexible |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | Qts too high |
EBP 50-100: works in either a sealed or ported alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| Faital PRO 4FE35 | 100 = | 0.83 +0.02 | 2.4 = | 2.73 +0.9 | 91 = | close | 8 Ω vs 16 Ω: amp load changes | + |
| Faital PRO 4FE35 | 100 = | 0.73 -0.08 | 2.4 = | 1.73 -0.1 | 91 = | close | 4 Ω vs 16 Ω: amp load changes · Xmax 1.73 mm < 1.83 mm: lower excursion-limited SPL | + |
| Faital PRO 4FE32 | 100 = | 0.61 -0.2 | 2.3 -0.1 | 2.73 +0.9 | 91 = | usable | 8 Ω vs 16 Ω: amp load changes | + |
| Faital PRO 4FE35 | 100 = | 1.16 +0.35 | 2.3 -0.1 | 1.83 = | 91 = | usable | + | |
| Faital PRO 4FE32 | 100 = | 0.53 -0.28 | 2.5 +0.1 | 1.73 -0.1 | 91 = | usable | 4 Ω vs 16 Ω: amp load changes · Xmax 1.73 mm < 1.83 mm: lower excursion-limited SPL | + |
| Eminence ALPHA 4-8 | 123 +23 | 0.75 -0.06 | 1.94 -0.46 | 2.6 +0.77 | 88 -3 | usable | 8 Ω vs 16 Ω: amp load changes | + |
| Eminence ALPHA 4-4 | 120 +20 | 0.63 -0.18 | 1.76 -0.64 | 2.6 +0.77 | 88 -3 | usable | 4 Ω vs 16 Ω: amp load changes | + |
| Faital PRO 4FE42 | 110 +10 | 0.47 -0.34 | 1.9 -0.5 | 2.83 +1 | 94 +3 | risky | 8 Ω vs 16 Ω: amp load changes | + |
| Sica 4 L 1 SL | 108.3 +8.3 | 0.63 -0.18 | 1.2 -1.2 | 2.4 +0.57 | 86.2 -4.8 | risky | 8 Ω vs 16 Ω: amp load changes | + |
| LaVoce WSN041.00-16 | 106 +6 | 0.36 -0.45 | 1.96 -0.44 | 4.3 +2.47 | 91 = | risky | + |
Compare the closest 3 against the 4FE32 →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.