Faital PRO 3FE22
Thiele-Small parameters
| Nominal size | 3" |
|---|---|
| Impedance | 16 Ω |
| Fs | 110 Hz |
| Qts | 0.56 |
| Qes | 0.64 |
| Qms | 4.6 |
| Vas | 1.4 L |
| Sd | 33 cm² |
| Xmax | 1.83 mm |
| Re | 12.3 Ω |
| Mms | 2.3 g |
| Pe | 20 W |
| Sensitivity | 91 dB |
Alignment hint
| EBP | 172 · ported |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 2.4 L |
EBP > 100: favours a ported (bass-reflex) alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| Faital PRO 3FE25 | 110 = | 0.52 -0.04 | 1.3 -0.1 | 1.73 -0.1 | 91 = | close | 4 Ω vs 16 Ω: amp load changes · Xmax 1.73 mm < 1.83 mm: lower excursion-limited SPL | + |
| Faital PRO 3FE25 | 110 = | 0.66 +0.1 | 1.3 -0.1 | 1.83 = | 91 = | close | 8 Ω vs 16 Ω: amp load changes | + |
| Faital PRO 3FE22 | 110 = | 0.47 -0.09 | 1.3 -0.1 | 1.83 = | 91 = | close | 8 Ω vs 16 Ω: amp load changes | + |
| Faital PRO 3FE25 | 110 = | 0.83 +0.27 | 1.3 -0.1 | 1.83 = | 90 -1 | usable | + | |
| Faital PRO 3FE22 | 110 = | 0.36 -0.2 | 1.3 -0.1 | 1.73 -0.1 | 91 = | usable | 4 Ω vs 16 Ω: amp load changes · Xmax 1.73 mm < 1.83 mm: lower excursion-limited SPL | + |
| Eminence ALPHA 3-8 | 118 +8 | 0.5 -0.06 | 0.95 -0.45 | 2.4 +0.57 | 88.6 -2.4 | usable | 8 Ω vs 16 Ω: amp load changes | + |
| LaVoce WSF030.70 | 112 +2 | 0.61 +0.05 | 0.89 -0.51 | 3.3 +1.47 | 85.5 -5.5 | usable | 8 Ω vs 16 Ω: amp load changes | + |
| Eminence ALPHA 3-32 | 117 +7 | 0.74 +0.18 | 0.98 -0.42 | 2.6 +0.77 | 88 -3 | usable | 32 Ω vs 16 Ω: amp load changes | + |
| Faital PRO 3FE26 | 150 +40 | 0.79 +0.23 | 0.9 -0.5 | 2 +0.17 | 90 -1 | risky | 8 Ω vs 16 Ω: amp load changes | + |
| Faital PRO 3FE26 | 150 +40 | 1.08 +0.52 | 0.9 -0.5 | 2 +0.17 | 90 -1 | risky | + |
Compare the closest 3 against the 3FE22 →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.