Faital PRO 15PR450
Thiele-Small parameters
| Nominal size | 15" |
|---|---|
| Impedance | 8 Ω |
| Fs | 35 Hz |
| Qts | 0.35 |
| Qes | 0.37 |
| Qms | 6.9 |
| Vas | 235.6 L |
| Sd | 857 cm² |
| Xmax | 6 mm |
| Re | 5.1 Ω |
| Mms | 90 g |
| Pe | 400 W |
| Sensitivity | 98 dB |
Alignment hint
| EBP | 95 · flexible |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 76.5 L |
EBP 50-100: works in either a sealed or ported alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| Beyma 15LX60 | 35 = | 0.346 = | 215 -20.6 | 9 +3 | 97.7 -0.3 | close | + | |
| Supravox 400 GMF PRO MK2 | 35 = | 0.32 -0.03 | 247 +11.4 | 5.8 -0.2 | 97.9 -0.1 | close | 200 W vs 400 W: lower power handling · Xmax 5.8 mm < 6 mm: lower excursion-limited SPL | + |
| PD PDN 15BR40 | 35.7 +0.7 | 0.338 -0.01 | 224.8 -10.8 | 9.8 +3.8 | 98.5 +0.5 | close | + | |
| Precision Devices PDN 15BR40 | 35.7 +0.7 | 0.338 -0.01 | 224.8 -10.8 | 9.8 +3.8 | 98.5 +0.5 | close | + | |
| Faital PRO 15PR400 v2021 | 35 = | 0.322 -0.03 | 248.9 +13.3 | 5.8 -0.2 | 98.9 +0.9 | close | Xmax 5.8 mm < 6 mm: lower excursion-limited SPL | + |
| Beyma 15LW30 v2015 | 34 -1 | 0.325 -0.02 | 251 +15.4 | 7 +1 | 97.6 -0.4 | close | + | |
| Fane SOVEREIGN 15-600LF | 37 +2 | 0.388 +0.04 | 236 +0.4 | 6.9 +0.9 | 98.3 +0.3 | close | + | |
| Fane SOVEREIGN 15-600LF v2015 | 37 +2 | 0.388 +0.04 | 236 +0.4 | 6.9 +0.9 | 98.3 +0.3 | close | + | |
| Faital PRO 15PR400 | 35 = | 0.32 -0.03 | 248.9 +13.3 | 5.75 -0.25 | 99 +1 | close | Xmax 5.75 mm < 6 mm: lower excursion-limited SPL | + |
| Focal 15PR75-200 | 36 +1 | 0.382 +0.03 | 224 -11.6 | 5.7 -0.3 | 97.4 -0.6 | close | 200 W vs 400 W: lower power handling · Xmax 5.7 mm < 6 mm: lower excursion-limited SPL | + |
Compare the closest 3 against the 15PR450 →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.