Faital PRO 12PR300
Thiele-Small parameters
| Nominal size | 12" |
|---|---|
| Impedance | 4 Ω |
| Fs | 50 Hz |
| Qts | 0.41 |
| Qes | 0.42 |
| Qms | 19.4 |
| Vas | 73.9 L |
| Sd | 533 cm² |
| Xmax | 4.92 mm |
| Re | 3.3 Ω |
| Mms | 54.4 g |
| Pe | 300 W |
| Sensitivity | 97 dB |
Alignment hint
| EBP | 119 · ported |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 37.4 L |
EBP > 100: favours a ported (bass-reflex) alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| PHL Audio 4511 | 48 -2 | 0.406 = | 74.1 +0.2 | 5.4 +0.48 | 96.2 -0.8 | close | 8 Ω vs 4 Ω: amp load changes | + |
| Faital PRO 12PR310 | 50 = | 0.42 +0.01 | 77.3 +3.4 | 4.92 = | 98 +1 | close | + | |
| SB Audience BIANCO-12MW200 | 50 = | 0.389 -0.02 | 68.7 -5.2 | 6 +1.08 | 97.2 +0.2 | close | 8 Ω vs 4 Ω: amp load changes | + |
| Fane SOVEREIGN 12-300 v2024 | 47 -3 | 0.4 -0.01 | 80 +6.1 | 5 +0.08 | 96.3 -0.7 | close | 8 Ω vs 4 Ω: amp load changes | + |
| Faital PRO 12PR310-4 | 50 = | 0.417 +0.01 | 66.1 -7.8 | 4.9 -0.02 | 98.7 +1.7 | close | Xmax 4.9 mm < 4.92 mm: lower excursion-limited SPL | + |
| Faital PRO 12PR330 | 50 = | 0.4 -0.01 | 79.1 +5.2 | 7.37 +2.45 | 98 +1 | close | 8 Ω vs 4 Ω: amp load changes | + |
| Sica 12 PF 3 | 47 -3 | 0.39 -0.02 | 76.5 +2.6 | 5.5 +0.58 | 96.4 -0.6 | close | 8 Ω vs 4 Ω: amp load changes | + |
| Faital PRO 12PR310 | 54 +4 | 0.4 -0.01 | 73.5 -0.4 | 4.92 = | 99 +2 | close | 8 Ω vs 4 Ω: amp load changes | + |
| PHL Audio 4531 v2023 | 46 -4 | 0.399 -0.01 | 71.9 -2 | 5.6 +0.68 | 95.9 -1.1 | close | 8 Ω vs 4 Ω: amp load changes | + |
| SICA 12 BP 2.5 CS | 46.8 -3.2 | 0.425 +0.02 | 81.3 +7.4 | 5 +0.08 | 96.4 -0.6 | close | 8 Ω vs 4 Ω: amp load changes · 200 W vs 300 W: lower power handling | + |
Compare the closest 3 against the 12PR300 →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.