← all drivers

Faital PRO 10HP1020

10" · 8 Ω · 700 W · 96 dB · datasheet ↗

Thiele-Small parameters

Nominal size10"
Impedance8 Ω
Fs60 Hz
Qts0.24
Qes0.25
Qms6.5
Vas16.1 L
Sd345 cm²
Xmax9 mm
Re5.5 Ω
Mms72.5 g
Pe700 W
Sensitivity96 dB

Alignment hint

EBP240 · ported
Sealed Vb (Qtc ≈ 0.71)≈ 2.1 L

EBP > 100: favours a ported (bass-reflex) alignment.

Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.

Substitute candidates

DriverFs (Hz)QtsVas (L)Xmax (mm)Sens (dB)FitNotesCompare
B&C 10NDL8861 +10.25 +0.0118.4 +2.38.1 -0.996 =closeXmax 8.1 mm < 9 mm: lower excursion-limited SPL+
B&C 10NW7667 +70.26 +0.0217.6 +1.56.8 -2.296.5 +0.5usable400 W vs 700 W: lower power handling · Xmax 6.8 mm < 9 mm: lower excursion-limited SPL+
Faital PRO 10FH50060 =0.25 +0.0124.2 +8.17.25 -1.7596 =usable4 Ω vs 8 Ω: amp load changes · 500 W vs 700 W: lower power handling · Xmax 7.25 mm < 9 mm: lower excursion-limited SPL+
Faital PRO 10FH53060 =0.25 +0.0123.5 +7.47.5 -1.597 +1usable500 W vs 700 W: lower power handling · Xmax 7.5 mm < 9 mm: lower excursion-limited SPL+
Beyma 10MC700Nd63 +30.22 -0.0220 +3.97 -297 +1usableXmax 7 mm < 9 mm: lower excursion-limited SPL+
18 Sound 10NTLW250061 +10.27 +0.0322 +5.97.6 -1.496.5 +0.5usable4 Ω vs 8 Ω: amp load changes · 500 W vs 700 W: lower power handling · Xmax 7.6 mm < 9 mm: lower excursion-limited SPL+
B&C 10BG7649 -110.22 -0.0216.7 +0.69.6 +0.691.5 -4.5usable500 W vs 700 W: lower power handling+
Faital PRO 10FH50060 =0.26 +0.0225.8 +9.77.5 -1.596 =usable500 W vs 700 W: lower power handling · Xmax 7.5 mm < 9 mm: lower excursion-limited SPL+
B&C 10NDL8867 +70.32 +0.0815.6 -0.57.8 -1.295.5 -0.5usable16 Ω vs 8 Ω: amp load changes · Xmax 7.8 mm < 9 mm: lower excursion-limited SPL+
B&C 10NW6459 -10.26 +0.0222 +5.96 -396 =usable300 W vs 700 W: lower power handling · Xmax 6 mm < 9 mm: lower excursion-limited SPL+

Compare the closest 3 against the 10HP1020 →

Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.

Used in enclosures (0)

No enclosure in the catalog uses this driver yet.