Europsonic TS38/300
Thiele-Small parameters
| Nominal size | 15" |
|---|---|
| Impedance | 8 Ω |
| Fs | 30 Hz |
| Qts | 0.553 |
| Qes | 0.69 |
| Qms | 2.79 |
| Vas | 608.5 L |
| Sd | 855 cm² |
| Xmax | 4.5 mm |
| Re | 5.4 Ω |
| Bl | 8.4 T·m |
| Mms | 47.4 g |
| Pe | 150 W |
| Sensitivity | 97.5 dB |
Alignment hint
| EBP | 43 · sealed |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 958.3 L |
EBP < 50: favours a sealed (closed) alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| Celestion K15-200E | 32 +2 | 0.473 -0.08 | 386 -222.5 | 5 +0.5 | 97.7 +0.2 | usable | + | |
| Eminence LEGEND BP1525 | 32 +2 | 0.479 -0.07 | 397 -211.5 | 6.2 +1.7 | 96.9 -0.6 | usable | + | |
| Altec 415C | 24.6 -5.4 | 0.526 -0.03 | 749.2 +140.7 | 3 -1.5 | 97.4 -0.1 | usable | 50 W vs 150 W: lower power handling · Xmax 3 mm < 4.5 mm: lower excursion-limited SPL | + |
| Beyma HP15 | 28 -2 | 0.392 -0.16 | 500 -108.5 | 5 +0.5 | 96.5 -1 | usable | + | |
| Hyper Phase HP15-8 | 28 -2 | 0.392 -0.16 | 500 -108.5 | 5 +0.5 | 96.5 -1 | usable | + | |
| Altec 416-8 Heathkit | 26.9 -3.1 | 0.466 -0.09 | 498 -110.5 | 3.8 -0.7 | 94.6 -2.9 | usable | Xmax 3.8 mm < 4.5 mm: lower excursion-limited SPL | + |
| Stromberg-Carlson 15 PO | 24.6 -5.4 | 0.563 +0.01 | 461.6 -146.9 | 5 +0.5 | 91.8 -5.7 | usable | 16 Ω vs 8 Ω: amp load changes | + |
| Supravox 400-2000EXC_07V | 25 -5 | 0.599 +0.05 | 444 -164.5 | 5 +0.5 | 93.3 -4.2 | usable | + | |
| Celestion K15-100 | 35 +5 | 0.594 +0.04 | 342 -266.5 | 5 +0.5 | 96.2 -1.3 | usable | 100 W vs 150 W: lower power handling | + |
| Eminence BETA-15A | 35 +5 | 0.58 +0.03 | 334.6 -273.9 | 4 -0.5 | 98.2 +0.7 | usable | Xmax 4 mm < 4.5 mm: lower excursion-limited SPL | + |
Compare the closest 3 against the TS38/300 →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.