Eminence KAPPALITE 3015 LF v2014
Thiele-Small parameters
| Nominal size | 15" |
|---|---|
| Impedance | 8 Ω |
| Fs | 43.7 Hz |
| Qts | 0.456 |
| Qes | 0.48 |
| Qms | 8.97 |
| Vas | 150.9 L |
| Sd | 881.1 cm² |
| Xmax | 6.6 mm |
| Re | 5.5 Ω |
| Bl | 17.4 T·m |
| Mms | 95.9 g |
| Pe | 450 W |
| Sensitivity | 97.8 dB |
Alignment hint
| EBP | 91 · flexible |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 107.4 L |
EBP 50-100: works in either a sealed or ported alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| Eminence KAPPALITE 3015 LF v2016 | 43.7 = | 0.456 = | 150.9 = | 6.6 = | 97.8 = | close | + | |
| Eminence KAPPALITE 3015 LF v2018 | 44 +0.3 | 0.456 = | 150.9 = | 6.6 = | 97.9 +0.1 | close | + | |
| Eminence KappaLITE 3015LF | 44 +0.3 | 0.46 = | 150.9 = | 9.6 +3 | 98.4 +0.6 | close | + | |
| Beyma 15MC500 | 46 +2.3 | 0.45 -0.01 | 134 -16.9 | 8 +1.4 | 98 +0.2 | close | + | |
| RCF L 15P530 | 45 +1.3 | 0.478 +0.02 | 160 +9.1 | 6.2 -0.4 | 98.5 +0.7 | close | 350 W vs 450 W: lower power handling · Xmax 6.2 mm < 6.6 mm: lower excursion-limited SPL | + |
| Beyma 15MCS500-8 | 46 +2.3 | 0.47 +0.01 | 133.5 -17.4 | 6.5 -0.1 | 97.5 -0.3 | close | Xmax 6.5 mm < 6.6 mm: lower excursion-limited SPL | + |
| MCM Electronics 55-3243 | 43.6 -0.1 | 0.465 +0.01 | 127.5 -23.4 | 6.2 -0.4 | 98.5 +0.7 | close | 4 Ω vs 8 Ω: amp load changes · Xmax 6.2 mm < 6.6 mm: lower excursion-limited SPL | + |
| LaVoce WAN153.00 | 43 -0.7 | 0.411 -0.05 | 137 -13.9 | 6.7 +0.1 | 98.3 +0.5 | close | + | |
| Beyma 15MCS500 | 46 +2.3 | 0.48 +0.02 | 134 -16.9 | 8 +1.4 | 98 +0.2 | close | + | |
| BMS 15N630 | 39 -4.7 | 0.42 -0.04 | 152 +1.1 | 8 +1.4 | 98 +0.2 | close | + |
Compare the closest 3 against the KAPPALITE 3015 LF v2014 →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.