Eminence DELTALITE 2512 |
Thiele-Small parameters
| Nominal size | 12" |
|---|---|
| Impedance | 8 Ω |
| Fs | 53.1 Hz |
| Qts | 0.52 |
| Qes | 0.64 |
| Qms | 2.94 |
| Vas | 67.44 L |
| Sd | 519.5 cm² |
| Xmax | 4.9 mm |
| Re | 5.28 Ω |
| Bl | 11.6 T·m |
| Mms | 48.58 g |
| Pe | 250 W |
| Sensitivity | 99.6 dB |
Alignment hint
| EBP | 83 · flexible |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 79.4 L |
EBP 50-100: works in either a sealed or ported alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| Faital PRO 12FE400 | 55 +1.9 | 0.52 = | 69.1 +1.66 | 5.42 +0.52 | 95 -4.6 | close | 4 Ω vs 8 Ω: amp load changes | + |
| Eminence DELTA 12 LFC | 52 -1.1 | 0.445 -0.08 | 63.7 -3.74 | 4.8 -0.1 | 98.8 -0.8 | close | 4 Ω vs 8 Ω: amp load changes · Xmax 4.8 mm < 4.9 mm: lower excursion-limited SPL | + |
| Eminence DELTA 12 LFA | 51 -2.1 | 0.477 -0.04 | 67.9 +0.46 | 4.8 -0.1 | 95.7 -3.9 | close | Xmax 4.8 mm < 4.9 mm: lower excursion-limited SPL | + |
| Faital PRO 12FE400 | 55 +1.9 | 0.57 +0.05 | 73.6 +6.16 | 5.42 +0.52 | 97 -2.6 | close | + | |
| Fane 12-500LF | 50 -3.1 | 0.495 -0.03 | 66 -1.44 | 5.5 +0.6 | 95.2 -4.4 | close | + | |
| Fane SOVEREIGN 12-500LF | 50 -3.1 | 0.495 -0.03 | 66 -1.44 | 5.5 +0.6 | 95.2 -4.4 | close | + | |
| Eminence DELTA 12 LF v2 | 51 -2.1 | 0.477 -0.04 | 67.9 +0.46 | 4.6 -0.3 | 95.7 -3.9 | close | Xmax 4.6 mm < 4.9 mm: lower excursion-limited SPL | + |
| Faital PRO 12PR330 | 52 -1.1 | 0.49 -0.03 | 76.3 +8.86 | 7.27 +2.37 | 97 -2.6 | close | 16 Ω vs 8 Ω: amp load changes | + |
| B&C 12 CLX 64 | 54 +0.9 | 0.575 +0.05 | 74 +6.56 | 5.3 +0.4 | 96.3 -3.3 | close | + | |
| Faital PRO 12PR310-4 | 50 -3.1 | 0.417 -0.1 | 66.1 -1.34 | 4.9 = | 98.7 -0.9 | close | 4 Ω vs 8 Ω: amp load changes | + |
Compare the closest 3 against the DELTALITE 2512 | →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.