Ciare PW 465 ND
Thiele-Small parameters
| Nominal size | 18" |
|---|---|
| Impedance | 8 Ω |
| Fs | 37 Hz |
| Qts | 0.39 |
| Qes | 0.4 |
| Qms | 12.1 |
| Vas | 141.16 L |
| Sd | 1089 cm² |
| Xmax | 11.5 mm |
| Re | 6 Ω |
| Bl | 28.5 T·m |
| Mms | 220.3 g |
| Pe | 1000 W |
| Sensitivity | 94.4 dB |
Alignment hint
| EBP | 93 · flexible |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 61.7 L |
EBP 50-100: works in either a sealed or ported alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| B&C 18TBW100 | 35 -2 | 0.39 = | 175 +33.84 | 12 +0.5 | 96 +1.6 | close | + | |
| B&C 18SW100 | 36 -1 | 0.36 -0.03 | 160 +18.84 | 12.5 +1 | 96 +1.6 | close | 4 Ω vs 8 Ω: amp load changes | + |
| Eminence NSW4018-8 | 36 -1 | 0.38 -0.01 | 164.49 +23.33 | 15.21 +3.71 | 96.6 +2.2 | close | + | |
| SB Audience NERO-18SW1900D | 34 -3 | 0.419 +0.03 | 158 +16.84 | 10.8 -0.7 | 95.4 +1 | close | Xmax 10.8 mm < 11.5 mm: lower excursion-limited SPL | + |
| LaVoce SAN184.03 | 36 -1 | 0.417 +0.03 | 160 +18.84 | 9.4 -2.1 | 95.9 +1.5 | close | Xmax 9.4 mm < 11.5 mm: lower excursion-limited SPL | + |
| LaVoce SAF184.04 | 37 = | 0.474 +0.08 | 143 +1.84 | 9.3 -2.2 | 95.2 +0.8 | close | Xmax 9.3 mm < 11.5 mm: lower excursion-limited SPL | + |
| B&C 18SW100 | 35 -2 | 0.38 -0.01 | 180 +38.84 | 12.5 +1 | 97 +2.6 | close | + | |
| B&C 18 TBW 100 | 32 -5 | 0.39 = | 175 +33.84 | 10.3 -1.2 | 95.2 +0.8 | usable | Xmax 10.3 mm < 11.5 mm: lower excursion-limited SPL | + |
| 18 Sound 18TLW3000 | 33 -4 | 0.41 +0.02 | 185 +43.84 | 12 +0.5 | 95 +0.6 | usable | + | |
| Faital PRO 18HP1030 v2018 | 35 -2 | 0.415 +0.02 | 162.1 +20.94 | 9.5 -2 | 96.1 +1.7 | usable | Xmax 9.5 mm < 11.5 mm: lower excursion-limited SPL | + |
Compare the closest 3 against the PW 465 ND →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.