Ciare CH250
Thiele-Small parameters
| Nominal size | 10" |
|---|---|
| Impedance | 4 Ω |
| Fs | 65 Hz |
| Qts | 1.367 |
| Qes | 1.53 |
| Qms | 12.8 |
| Vas | 52 L |
| Sd | 320 cm² |
| Xmax | 0.5 mm |
| Re | 3.4 Ω |
| Bl | 3.9 T·m |
| Mms | 16.6 g |
| Pe | 50 W |
| Sensitivity | 95.4 dB |
Alignment hint
| EBP | 42 · sealed |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | Qts too high |
EBP < 50: favours a sealed (closed) alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| Audax 21PA12 RV | 57.2 -7.8 | 1.462 +0.09 | 57.6 +5.6 | 1 +0.5 | 92.5 -2.9 | usable | 10 W vs 50 W: lower power handling | + |
| SICA LP 266.25 / 280 ER 4 | 75 +10 | 1.311 -0.06 | 40.6 -11.4 | 1.5 +1 | 96.9 +1.5 | usable | + | |
| SICA 10 D 1 CS | 76.1 +11.1 | 1.564 +0.2 | 43.9 -8.1 | 1.5 +1 | 93.2 -2.2 | usable | 8 Ω vs 4 Ω: amp load changes | + |
| Beyma HP10 | 61 -4 | 1.057 -0.31 | 51 -1 | 3.1 +2.6 | 92.1 -3.3 | usable | 8 Ω vs 4 Ω: amp load changes | + |
| Jinwey YDA-250-4 | 58.3 -6.7 | 1.291 -0.08 | 36.6 -15.4 | 2 +1.5 | 92.2 -3.2 | usable | + | |
| Celestion G10-GB | 93.8 +28.8 | 1.398 +0.03 | 33 -19 | 1 +0.5 | 94.9 -0.5 | usable | 8 Ω vs 4 Ω: amp load changes · 30 W vs 50 W: lower power handling | + |
| Jinwey YDA-250-8 | 60.1 -4.9 | 1.473 +0.11 | 35.8 -16.2 | 1.9 +1.4 | 89 -6.4 | usable | 8 Ω vs 4 Ω: amp load changes | + |
| Jensen CR10 | 96 +31 | 1.435 +0.07 | 29.7 -22.3 | 0.8 +0.3 | 94.8 -0.6 | usable | 8 Ω vs 4 Ω: amp load changes · 25 W vs 50 W: lower power handling | + |
| Visaton W250 vp | 55.6 -9.4 | 1.045 -0.32 | 58.1 +6.1 | 3.4 +2.9 | 91.9 -3.5 | usable | 8 Ω vs 4 Ω: amp load changes | + |
| SICA 10 D 1.5 CS - 4 Ohms | 69 +4 | 0.842 -0.52 | 42.5 -9.5 | 1 +0.5 | 98.1 +2.7 | usable | + |
Compare the closest 3 against the CH250 →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.