Celestion G12T 75
Thiele-Small parameters
| Nominal size | 12" |
|---|---|
| Impedance | 16 Ω |
| Fs | 85 Hz |
| Qts | 0.836 |
| Qes | 0.91 |
| Qms | 10.3 |
| Vas | 51 L |
| Sd | 517 cm² |
| Xmax | 2 mm |
| Re | 12.9 Ω |
| Bl | 14 T·m |
| Mms | 25.8 g |
| Pe | 75 W |
| Sensitivity | 95.3 dB |
Alignment hint
| EBP | 93 · flexible |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | Qts too high |
EBP 50-100: works in either a sealed or ported alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| Celestion G12T-100 | 81 -4 | 0.833 = | 47 -4 | 2 = | 96.8 +1.5 | close | 8 Ω vs 16 Ω: amp load changes | + |
| Celestion F12M-150 Triple Cone | 69.4 -15.6 | 0.906 +0.07 | 46.9 -4.1 | 2.3 +0.3 | 95.2 -0.1 | close | 8 Ω vs 16 Ω: amp load changes | + |
| Celestion F12-X200 | 75 -10 | 0.777 -0.06 | 47.3 -3.7 | 3 +1 | 97.1 +1.8 | usable | 8 Ω vs 16 Ω: amp load changes | + |
| JBL 2142H | 72 -13 | 0.755 -0.08 | 45.3 -5.7 | 2.2 +0.2 | 96.5 +1.2 | usable | 8 Ω vs 16 Ω: amp load changes | + |
| Celestion TF 1215 | 62 -23 | 0.857 +0.02 | 69 +18 | 2.5 +0.5 | 96.2 +0.9 | usable | 8 Ω vs 16 Ω: amp load changes | + |
| Siemens KL405 | 75.8 -9.2 | 0.77 -0.07 | 68 +17 | 3 +1 | 99.2 +3.9 | usable | 8 Ω vs 16 Ω: amp load changes | + |
| B&C 320K/C-A | 82 -3 | 0.59 -0.25 | 52 +1 | 2 = | 100 +4.7 | usable | + | |
| Fane 12-100TC | 56 -29 | 0.779 -0.06 | 56.1 +5.1 | 2.5 +0.5 | 93.5 -1.8 | usable | 8 Ω vs 16 Ω: amp load changes | + |
| Jensen JCH 1270-8 | 78 -7 | 1.084 +0.25 | 46.7 -4.3 | 1.5 -0.5 | 96.6 +1.3 | usable | 8 Ω vs 16 Ω: amp load changes · Xmax 1.5 mm < 2 mm: lower excursion-limited SPL | + |
| SICA 12 D 1.5 CS 8 Ohms | 62 -23 | 0.748 -0.09 | 63.5 +12.5 | 2.7 +0.7 | 96.8 +1.5 | usable | 8 Ω vs 16 Ω: amp load changes | + |
Compare the closest 3 against the G12T 75 →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.