Celestion G10-GB
Thiele-Small parameters
| Nominal size | 10" |
|---|---|
| Impedance | 8 Ω |
| Fs | 93.8 Hz |
| Qts | 1.398 |
| Qes | 1.748 |
| Qms | 6.992 |
| Vas | 33 L |
| Sd | 323.7 cm² |
| Xmax | 1 mm |
| Re | 6.4 Ω |
| Bl | 5.3 T·m |
| Mms | 12.8 g |
| Pe | 30 W |
| Sensitivity | 94.9 dB |
Alignment hint
| EBP | 54 · flexible |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | Qts too high |
EBP 50-100: works in either a sealed or ported alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| Jensen CR10 | 96 +2.2 | 1.435 +0.04 | 29.7 -3.3 | 0.8 -0.2 | 94.8 -0.1 | close | Xmax 0.8 mm < 1 mm: lower excursion-limited SPL | + |
| Beyma 10AGN | 90 -3.8 | 1.319 -0.08 | 30 -3 | 1.6 +0.6 | 93 -1.9 | close | + | |
| Jensen P10R | 97 +3.2 | 1.46 +0.06 | 27.4 -5.6 | 0.8 -0.2 | 94.6 -0.3 | close | Xmax 0.8 mm < 1 mm: lower excursion-limited SPL | + |
| SICA LP 266.25 / 280 ER 4 | 75 -18.8 | 1.311 -0.09 | 40.6 +7.6 | 1.5 +0.5 | 96.9 +2 | usable | 4 Ω vs 8 Ω: amp load changes | + |
| Jensen JCH 1035-8 | 107 +13.2 | 1.435 +0.04 | 22.4 -10.6 | 0.9 -0.1 | 98.2 +3.3 | usable | 4 Ω vs 8 Ω: amp load changes · Xmax 0.9 mm < 1 mm: lower excursion-limited SPL | + |
| SICA 10 D 1 CS | 76.1 -17.7 | 1.564 +0.17 | 43.9 +10.9 | 1.5 +0.5 | 93.2 -1.7 | usable | + | |
| Jinwey YDA-250-4 | 58.3 -35.5 | 1.291 -0.11 | 36.6 +3.6 | 2 +1 | 92.2 -2.7 | usable | 4 Ω vs 8 Ω: amp load changes | + |
| Eminence LEGEND 1058 | 97 +3.2 | 1.133 -0.26 | 26.4 -6.6 | 0.5 -0.5 | 95.3 +0.4 | usable | Xmax 0.5 mm < 1 mm: lower excursion-limited SPL | + |
| Jinwey YDA-250-8 | 60.1 -33.7 | 1.473 +0.08 | 35.8 +2.8 | 1.9 +0.9 | 89 -5.9 | usable | + | |
| Celestion TF 1015 | 85 -8.8 | 1.049 -0.35 | 21 -12 | 1.4 +0.4 | 92.9 -2 | usable | + |
Compare the closest 3 against the G10-GB →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.