Celestion FTR18-4080F
Thiele-Small parameters
| Nominal size | 18" |
|---|---|
| Impedance | 8 Ω |
| Fs | 28 Hz |
| Qts | 0.265 |
| Qes | 0.28 |
| Qms | 5.12 |
| Vas | 383.3 L |
| Sd | 1130 cm² |
| Xmax | 6 mm |
| Re | 5.27 Ω |
| Bl | 22.4 T·m |
| Mms | 150.9 g |
| Pe | 800 W |
| Sensitivity | 98.6 dB |
Alignment hint
| EBP | 100 · flexible |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 62.6 L |
EBP 50-100: works in either a sealed or ported alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| Rockford Fosgate SPP-184 | 27 -1 | 0.266 = | 353 -30.3 | 6 = | 99.2 +0.6 | close | 4 Ω vs 8 Ω: amp load changes · 350 W vs 800 W: lower power handling | + |
| RCF LF 18X400 | 28 = | 0.255 -0.01 | 360 -23.3 | 9 +3 | 98.6 = | close | + | |
| RCF LF 18G400 | 28 = | 0.273 +0.01 | 360 -23.3 | 9 +3 | 98.3 -0.3 | close | + | |
| Electro-Voice EVX-180A | 29 +1 | 0.27 +0.01 | 416 +32.7 | 6.4 +0.4 | 99.5 +0.9 | close | 600 W vs 800 W: lower power handling | + |
| Electro-Voice EVX-180B | 29 +1 | 0.27 +0.01 | 416 +32.7 | 6.4 +0.4 | 99.5 +0.9 | close | 600 W vs 800 W: lower power handling | + |
| RCF LF18G400 | 28 = | 0.27 +0.01 | 360 -23.3 | 9 +3 | 97.5 -1.1 | close | + | |
| Celestion FTR18-4080FD | 26 -2 | 0.27 +0.01 | 395.56 +12.26 | 6 = | 97 -1.6 | close | + | |
| PD PD 182 | 28 = | 0.238 -0.03 | 391 +7.7 | 8.2 +2.2 | 98.7 +0.1 | close | 600 W vs 800 W: lower power handling | + |
| Precision Devices PD 182 | 28 = | 0.238 -0.03 | 391 +7.7 | 8.2 +2.2 | 98.7 +0.1 | close | 600 W vs 800 W: lower power handling | + |
| Faital PRO 18FH510 | 30 +2 | 0.26 -0.01 | 391.4 +8.1 | 9.45 +3.45 | 98 -0.6 | close | 4 Ω vs 8 Ω: amp load changes · 600 W vs 800 W: lower power handling | + |
Compare the closest 3 against the FTR18-4080F →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.