Celestion BL15-300X
Thiele-Small parameters
| Nominal size | 15" |
|---|---|
| Impedance | 4 Ω |
| Fs | 48 Hz |
| Qts | 0.447 |
| Qes | 0.525 |
| Qms | 3.025 |
| Vas | 158.8 L |
| Sd | 707 cm² |
| Xmax | 4.3 mm |
| Re | 3.15 Ω |
| Bl | 9.4 T·m |
| Mms | 48.5 g |
| Pe | 300 W |
| Sensitivity | 101.3 dB |
Alignment hint
| EBP | 91 · flexible |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 105.7 L |
EBP 50-100: works in either a sealed or ported alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| JBL 2033H | 50 +2 | 0.417 -0.03 | 170 +11.2 | 4.9 +0.6 | 100.7 -0.6 | close | 8 Ω vs 4 Ω: amp load changes | + |
| Jensen BN15/350SB vp | 45 -3 | 0.461 +0.01 | 163 +4.2 | 5 +0.7 | 98.8 -2.5 | close | 8 Ω vs 4 Ω: amp load changes | + |
| Jensen BN15/350A vp | 45 -3 | 0.461 +0.01 | 163.1 +4.3 | 5.5 +1.2 | 98.8 -2.5 | close | 8 Ω vs 4 Ω: amp load changes | + |
| B&C 15 CX 40 | 44 -4 | 0.43 -0.02 | 162 +3.2 | 4.5 +0.2 | 98.7 -2.6 | close | 8 Ω vs 4 Ω: amp load changes | + |
| Peavey 1505-8 DT | 46.5 -1.5 | 0.389 -0.06 | 164.3 +5.5 | 5.1 +0.8 | 99.5 -1.8 | close | 8 Ω vs 4 Ω: amp load changes | + |
| Peavey 1505-8BW | 46.5 -1.5 | 0.389 -0.06 | 164.3 +5.5 | 5.1 +0.8 | 99.5 -1.8 | close | 8 Ω vs 4 Ω: amp load changes | + |
| RCF L 15P530 | 45 -3 | 0.478 +0.03 | 160 +1.2 | 6.2 +1.9 | 98.5 -2.8 | close | 8 Ω vs 4 Ω: amp load changes | + |
| RCF MB 15X301 (prodance) | 50.6 +2.6 | 0.44 -0.01 | 133.8 -25 | 5.9 +1.6 | 99.2 -2.1 | close | 8 Ω vs 4 Ω: amp load changes | + |
| SICA 15 CX 3 PL | 44.5 -3.5 | 0.407 -0.04 | 152.4 -6.4 | 5.5 +1.2 | 99 -2.3 | close | 8 Ω vs 4 Ω: amp load changes | + |
| Eminence KAPPA PRO 15 | 47 -1 | 0.381 -0.07 | 167.7 +8.9 | 6.4 +2.1 | 100.2 -1.1 | close | 8 Ω vs 4 Ω: amp load changes | + |
Compare the closest 3 against the BL15-300X →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.