BMS 15CN860
Thiele-Small parameters
| Nominal size | 15" |
|---|---|
| Impedance | 8 Ω |
| Fs | 46 Hz |
| Qts | 0.276 |
| Qes | 0.3 |
| Qms | 3.5 |
| Vas | 102 L |
| Sd | 804 cm² |
| Xmax | 6 mm |
| Re | 5.7 Ω |
| Bl | 24.2 T·m |
| Mms | 106.3 g |
| Pe | 1000 W |
| Sensitivity | 98.7 dB |
Alignment hint
| EBP | 153 · ported |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 18.3 L |
EBP > 100: favours a ported (bass-reflex) alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| Sica 15 F 4 CP | 46.4 +0.4 | 0.27 -0.01 | 97 -5 | 7 +1 | 99.4 +0.7 | close | 700 W vs 1000 W: lower power handling | + |
| B&C 14 NDL 88 | 45 -1 | 0.298 +0.02 | 102 = | 6.7 +0.7 | 98.8 +0.1 | close | 700 W vs 1000 W: lower power handling | + |
| Beyma 15P1000FEV2 | 42 -4 | 0.278 = | 100.2 -1.8 | 6.5 +0.5 | 97.9 -0.8 | close | + | |
| Sica 15 K 4 PL | 46.5 +0.5 | 0.3 +0.02 | 102.3 +0.3 | 8 +2 | 99.2 +0.5 | close | + | |
| B&C 14 CXN 88 | 46 = | 0.265 -0.01 | 100 -2 | 5.2 -0.8 | 99.9 +1.2 | close | 500 W vs 1000 W: lower power handling · Xmax 5.2 mm < 6 mm: lower excursion-limited SPL | + |
| Oberton 15MB701 | 44.24 -1.76 | 0.268 -0.01 | 100.22 -1.78 | 9.25 +3.25 | 97.5 -1.2 | close | 700 W vs 1000 W: lower power handling | + |
| Oberton 15XL701 | 45.25 -0.75 | 0.28 = | 116.99 +14.99 | 8.75 +2.75 | 98 -0.7 | close | 700 W vs 1000 W: lower power handling | + |
| B&C 15 NA 100 | 47 +1 | 0.277 = | 88 -14 | 5.1 -0.9 | 98.9 +0.2 | close | Xmax 5.1 mm < 6 mm: lower excursion-limited SPL | + |
| Ciare NDH 15-4 | 48.6 +2.6 | 0.312 +0.04 | 96.9 -5.1 | 5.9 -0.1 | 98.6 -0.1 | close | Xmax 5.9 mm < 6 mm: lower excursion-limited SPL | + |
| B&C 15NA100 | 47 +1 | 0.28 = | 88 -14 | 10 +4 | 98 -0.7 | close | + |
Compare the closest 3 against the 15CN860 →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.