Beyma 18P1200Nd vp459
Thiele-Small parameters
| Nominal size | 18" |
|---|---|
| Impedance | 8 Ω |
| Fs | 43.8 Hz |
| Qts | 0.376 |
| Qes | 0.39 |
| Qms | 10.12 |
| Vas | 124.9 L |
| Sd | 1256.6 cm² |
| Xmax | 6.3 mm |
| Re | 5.04 Ω |
| Bl | 28.8 T·m |
| Mms | 234 g |
| Pe | 1200 W |
| Sensitivity | 98.3 dB |
Alignment hint
| EBP | 112 · ported |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 49.2 L |
EBP > 100: favours a ported (bass-reflex) alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| Beyma 18P1200Nd vp1 | 43.8 = | 0.376 = | 116.9 -8 | 6.1 -0.2 | 98 -0.3 | close | Xmax 6.1 mm < 6.3 mm: lower excursion-limited SPL | + |
| PRV Audio 18SW3000 | 43.7 -0.1 | 0.342 -0.03 | 111.3 -13.6 | 6.7 +0.4 | 98.1 -0.2 | close | + | |
| PD PD 1852 | 40 -3.8 | 0.33 -0.05 | 129.1 +4.2 | 6.2 -0.1 | 97.2 -1.1 | close | Xmax 6.2 mm < 6.3 mm: lower excursion-limited SPL | + |
| Precision Devices PD 1852 | 40 -3.8 | 0.33 -0.05 | 129.1 +4.2 | 6.2 -0.1 | 97.2 -1.1 | close | Xmax 6.2 mm < 6.3 mm: lower excursion-limited SPL | + |
| P.Audio C18-650EL v2009 | 45 +1.2 | 0.375 = | 158.3 +33.4 | 5.3 -1 | 99.4 +1.1 | close | Xmax 5.3 mm < 6.3 mm: lower excursion-limited SPL | + |
| Beyma 18P100FE | 40 -3.8 | 0.39 +0.01 | 163.2 +38.3 | 7.1 +0.8 | 98.1 -0.2 | close | + | |
| MAG Audio M 1805 | 37.5 -6.3 | 0.357 -0.02 | 138.5 +13.6 | 7.1 +0.8 | 96.7 -1.6 | close | + | |
| Celestion CF1840JD | 44.2 +0.4 | 0.444 +0.07 | 113.9 -11 | 8.5 +2.2 | 96.8 -1.5 | close | + | |
| B&C 18 PZB 46 | 37 -6.8 | 0.374 = | 155 +30.1 | 6.5 +0.2 | 96.8 -1.5 | usable | 700 W vs 1200 W: lower power handling | + |
| LaVoce SAN184.02 | 38 -5.8 | 0.406 +0.03 | 150 +25.1 | 7.9 +1.6 | 96.8 -1.5 | usable | + |
Compare the closest 3 against the 18P1200Nd vp459 →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.