Beyma 12MI100
Thiele-Small parameters
| Nominal size | 12" |
|---|---|
| Impedance | 8 Ω |
| Fs | 58 Hz |
| Qts | 0.221 |
| Qes | 0.23 |
| Qms | 5.54 |
| Vas | 64 L |
| Sd | 530 cm² |
| Xmax | 4.2 mm |
| Re | 6.3 Ω |
| Bl | 21.5 T·m |
| Mms | 46.3 g |
| Pe | 450 W |
| Sensitivity | 100.4 dB |
Alignment hint
| EBP | 252 · ported |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 6.9 L |
EBP > 100: favours a ported (bass-reflex) alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| JBL 2020 H | 60 +2 | 0.228 +0.01 | 65 +1 | 4 -0.2 | 101.9 +1.5 | close | Xmax 4 mm < 4.2 mm: lower excursion-limited SPL | + |
| JBL 2020H | 60 +2 | 0.228 +0.01 | 65 +1 | 4 -0.2 | 101.9 +1.5 | close | Xmax 4 mm < 4.2 mm: lower excursion-limited SPL | + |
| RCF MB 12N351 | 55 -3 | 0.201 -0.02 | 61 -3 | 4.7 +0.5 | 100.4 = | close | + | |
| Beyma 12"MI100 | 58 = | 0.22 = | 64 = | 3 -1.2 | 100 -0.4 | close | Xmax 3 mm < 4.2 mm: lower excursion-limited SPL | + |
| 18 Sound 12ND830 | 58 = | 0.24 +0.02 | 63 -1 | 6.5 +2.3 | 99 -1.4 | close | 4 Ω vs 8 Ω: amp load changes | + |
| Electro-Voice DL12X | 56 -2 | 0.233 +0.01 | 77 +13 | 4.1 -0.1 | 100.7 +0.3 | close | 300 W vs 450 W: lower power handling · Xmax 4.1 mm < 4.2 mm: lower excursion-limited SPL | + |
| RCF MB 12N301 | 54 -4 | 0.24 +0.02 | 71 +7 | 4.9 +0.7 | 99.7 -0.7 | close | + | |
| Precision Devices PD121 | 59 +1 | 0.201 -0.02 | 54 -10 | 5 +0.8 | 100 -0.4 | close | 16 Ω vs 8 Ω: amp load changes · 300 W vs 450 W: lower power handling | + |
| B&C 12 CXN 88 | 50 -8 | 0.224 = | 59 -5 | 4 -0.2 | 99.1 -1.3 | close | Xmax 4 mm < 4.2 mm: lower excursion-limited SPL | + |
| B&C 12MH32 | 53 -5 | 0.19 -0.03 | 63 -1 | 5 +0.8 | 101 +0.6 | close | + |
Compare the closest 3 against the 12MI100 →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.