← all drivers

Beyma 10MW/ND

10" · 6 Ω · 350 W · 93.5 dB

Thiele-Small parameters

Nominal size10"
Impedance6 Ω
Fs49 Hz
Qts0.32
Qes0.33
Qms9.95
Vas40.7 L
Sd350 cm²
Xmax7.5 mm
Re6 Ω
Bl1.5 T·m
Mms0.4 g
Pe350 W
Sensitivity93.5 dB

Alignment hint

EBP148 · ported
Sealed Vb (Qtc ≈ 0.71)≈ 10.5 L

EBP > 100: favours a ported (bass-reflex) alignment.

Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.

Substitute candidates

DriverFs (Hz)QtsVas (L)Xmax (mm)Sens (dB)FitNotesCompare
Beyma 10MW/ND v249 =0.319 =40.7 =6.1 -1.494.8 +1.3close8 Ω vs 6 Ω: amp load changes · Xmax 6.1 mm < 7.5 mm: lower excursion-limited SPL+
SICA 10 S 3 CP v201743 -60.313 -0.0139.9 -0.87 -0.593.6 +0.1close8 Ω vs 6 Ω: amp load changes · Xmax 7 mm < 7.5 mm: lower excursion-limited SPL+
18 Sound 10NW75053 +40.31 -0.0134 -6.77.5 =94 +0.5close8 Ω vs 6 Ω: amp load changes+
18 Sound 10NW75052 +30.36 +0.0438 -2.77.1 -0.494 +0.5close16 Ω vs 6 Ω: amp load changes · Xmax 7.1 mm < 7.5 mm: lower excursion-limited SPL+
Eminence KAPPALITE™ KL3010LF-845 -40.31 -0.0147.33 +6.638.52 +1.0292 -1.5close8 Ω vs 6 Ω: amp load changes+
Sica 10 S 3 CP42 -70.3 -0.0242.8 +2.17 -0.594 +0.5close8 Ω vs 6 Ω: amp load changes · Xmax 7 mm < 7.5 mm: lower excursion-limited SPL+
Ciare FXE 10-2.546 -30.358 +0.0441.6 +0.96 -1.593.6 +0.1close8 Ω vs 6 Ω: amp load changes · Xmax 6 mm < 7.5 mm: lower excursion-limited SPL+
Monacor SP-10/250PRO47 -20.331 +0.0140.7 =4.8 -2.793.3 -0.2close8 Ω vs 6 Ω: amp load changes · 250 W vs 350 W: lower power handling · Xmax 4.8 mm < 7.5 mm: lower excursion-limited SPL+
SICA 10 S 3 CP 8 Ohms48 -10.323 =32.4 -8.36.1 -1.494 +0.5close8 Ω vs 6 Ω: amp load changes · Xmax 6.1 mm < 7.5 mm: lower excursion-limited SPL+
Faital PRO 10RS35040 -90.31 -0.0140.6 -0.17.17 -0.3391 -2.5close4 Ω vs 6 Ω: amp load changes · Xmax 7.17 mm < 7.5 mm: lower excursion-limited SPL+

Compare the closest 3 against the 10MW/ND →

Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.

Used in enclosures (0)

No enclosure in the catalog uses this driver yet.