Beyma 10MCS500
Thiele-Small parameters
| Nominal size | 10" |
|---|---|
| Impedance | 8 Ω |
| Fs | 70 Hz |
| Qts | 0.366 |
| Qes | 0.38 |
| Qms | 10.1 |
| Vas | 18.8 L |
| Sd | 350 cm² |
| Xmax | 4.4 mm |
| Re | 5.7 Ω |
| Bl | 17.6 T·m |
| Mms | 47.2 g |
| Pe | 500 W |
| Sensitivity | 95.7 dB |
Alignment hint
| EBP | 184 · ported |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 6.9 L |
EBP > 100: favours a ported (bass-reflex) alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| P.Audio SN-10MB | 70 = | 0.397 +0.03 | 19 +0.2 | 5 +0.6 | 95.6 -0.1 | close | + | |
| SB Audience NERO-10MWN600D | 68 -2 | 0.339 -0.03 | 18.8 = | 3.9 -0.5 | 95.8 +0.1 | close | Xmax 3.9 mm < 4.4 mm: lower excursion-limited SPL | + |
| B&C 10 NDL 64 vp | 71 +1 | 0.361 -0.01 | 19 +0.2 | 3.1 -1.3 | 95.9 +0.2 | close | 250 W vs 500 W: lower power handling · Xmax 3.1 mm < 4.4 mm: lower excursion-limited SPL | + |
| B&C 10CLA64 | 74 +4 | 0.42 +0.05 | 18.5 -0.3 | 5 +0.6 | 96 +0.3 | close | 250 W vs 500 W: lower power handling | + |
| B&C 10CLA64 | 72 +2 | 0.41 +0.04 | 21 +2.2 | 4.5 +0.1 | 96 +0.3 | close | 16 Ω vs 8 Ω: amp load changes · 250 W vs 500 W: lower power handling | + |
| Faital PRO 10FH530 | 67 -3 | 0.39 +0.02 | 20.2 +1.4 | 7.45 +3.05 | 96 +0.3 | close | 16 Ω vs 8 Ω: amp load changes | + |
| 18 Sound 10NTLW2500 | 66 -4 | 0.39 +0.02 | 20.9 +2.1 | 7.6 +3.2 | 96 +0.3 | close | 16 Ω vs 8 Ω: amp load changes | + |
| BMS 10C262 | 65 -5 | 0.368 = | 25.5 +6.7 | 5.1 +0.7 | 95.7 = | close | + | |
| Faital PRO 10FH500 | 65 -5 | 0.42 +0.05 | 19.2 +0.4 | 7.25 +2.85 | 95 -0.7 | close | 16 Ω vs 8 Ω: amp load changes | + |
| 18 Sound 10NTLW3500 | 65 -5 | 0.35 -0.02 | 16 -2.8 | 7.9 +3.5 | 95 -0.7 | close | + |
Compare the closest 3 against the 10MCS500 →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.