B&C 8MBX51
Thiele-Small parameters
| Nominal size | 8" |
|---|---|
| Impedance | 8 Ω |
| Fs | 60 Hz |
| Qts | 0.29 |
| Qes | 0.31 |
| Qms | 5.6 |
| Vas | 23 L |
| Sd | 220 cm² |
| Xmax | 6 mm |
| Re | 4.9 Ω |
| Bl | 11.4 T·m |
| Mms | 20 g |
| Pe | 200 W |
| Sensitivity | 96.5 dB |
Alignment hint
| EBP | 194 · ported |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 4.7 L |
EBP > 100: favours a ported (bass-reflex) alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| B&C 8FMB51 | 67 +7 | 0.28 -0.01 | 20.7 -2.3 | 5.5 -0.5 | 96.5 = | close | Xmax 5.5 mm < 6 mm: lower excursion-limited SPL | + |
| Beyma 8"P300Fe/N | 53 -7 | 0.31 +0.02 | 24.8 +1.8 | 6 = | 94 -2.5 | close | + | |
| 18 Sound 8NMB420 | 59 -1 | 0.31 +0.02 | 31 +8 | 5.8 -0.2 | 95 -1.5 | usable | 4 Ω vs 8 Ω: amp load changes · Xmax 5.8 mm < 6 mm: lower excursion-limited SPL | + |
| 18 Sound 8NMB420 | 61 +1 | 0.28 -0.01 | 33 +10 | 5.8 -0.2 | 95 -1.5 | usable | Xmax 5.8 mm < 6 mm: lower excursion-limited SPL | + |
| B&C 8MDN51 | 68 +8 | 0.27 -0.02 | 17.5 -5.5 | 6 = | 97 +0.5 | usable | 16 Ω vs 8 Ω: amp load changes | + |
| 18 Sound 8NW650 | 62 +2 | 0.25 -0.04 | 18.99 -4.01 | 5.5 -0.5 | 95 -1.5 | usable | 16 Ω vs 8 Ω: amp load changes · Xmax 5.5 mm < 6 mm: lower excursion-limited SPL | + |
| Faital PRO 8PR210 | 65 +5 | 0.29 = | 15.4 -7.6 | 6.92 +0.92 | 95 -1.5 | usable | + | |
| 18 Sound 8NW650 | 63 +3 | 0.25 -0.04 | 17.8 -5.2 | 5.5 -0.5 | 96 -0.5 | usable | Xmax 5.5 mm < 6 mm: lower excursion-limited SPL | + |
| B&C 8MBX51 | 68 +8 | 0.38 +0.09 | 22 -1 | 6 = | 97 +0.5 | usable | 16 Ω vs 8 Ω: amp load changes | + |
| 18 Sound 8MB400 | 64 +4 | 0.38 +0.09 | 23.9 +0.9 | 5.8 -0.2 | 95 -1.5 | usable | Xmax 5.8 mm < 6 mm: lower excursion-limited SPL | + |
Compare the closest 3 against the 8MBX51 →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.