B&C 8MBX51
Thiele-Small parameters
| Nominal size | 8" |
|---|---|
| Impedance | 16 Ω |
| Fs | 68 Hz |
| Qts | 0.38 |
| Qes | 0.43 |
| Qms | 3.3 |
| Vas | 22 L |
| Sd | 220 cm² |
| Xmax | 6 mm |
| Re | 10.2 Ω |
| Bl | 13.7 T·m |
| Mms | 18.4 g |
| Pe | 200 W |
| Sensitivity | 97 dB |
Alignment hint
| EBP | 158 · ported |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 8.9 L |
EBP > 100: favours a ported (bass-reflex) alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| B&C 8FMB51 | 68 = | 0.39 +0.01 | 20.5 -1.5 | 5.5 -0.5 | 96 -1 | close | Xmax 5.5 mm < 6 mm: lower excursion-limited SPL | + |
| 18 Sound 8MB400 | 64 -4 | 0.38 = | 23.9 +1.9 | 5.8 -0.2 | 95 -2 | close | 8 Ω vs 16 Ω: amp load changes · Xmax 5.8 mm < 6 mm: lower excursion-limited SPL | + |
| 18 Sound 8NMB420 | 66 -2 | 0.41 +0.03 | 24.53 +2.53 | 5.8 -0.2 | 95 -2 | close | Xmax 5.8 mm < 6 mm: lower excursion-limited SPL | + |
| 18 Sound 8MB500 | 74 +6 | 0.43 +0.05 | 21.5 -0.5 | 6 = | 95 -2 | close | 8 Ω vs 16 Ω: amp load changes | + |
| 18 Sound 8MB500 | 73 +5 | 0.36 -0.02 | 18.4 -3.6 | 6 = | 95 -2 | close | 4 Ω vs 16 Ω: amp load changes | + |
| Beyma 8"G40 | 70 +2 | 0.36 -0.02 | 17 -5 | 6.5 +0.5 | 95 -2 | close | 8 Ω vs 16 Ω: amp load changes | + |
| B&C 8FMB51 | 67 -1 | 0.28 -0.1 | 20.7 -1.3 | 5.5 -0.5 | 96.5 -0.5 | usable | 8 Ω vs 16 Ω: amp load changes · Xmax 5.5 mm < 6 mm: lower excursion-limited SPL | + |
| B&C 8MBX51 | 60 -8 | 0.29 -0.09 | 23 +1 | 6 = | 96.5 -0.5 | usable | 8 Ω vs 16 Ω: amp load changes | + |
| 18 Sound 8MB500 | 73 +5 | 0.5 +0.12 | 21.3 -0.7 | 6 = | 95 -2 | usable | + | |
| Faital PRO 8PR200 | 58 -10 | 0.37 -0.01 | 16.9 -5.1 | 8.15 +2.15 | 95 -2 | usable | 8 Ω vs 16 Ω: amp load changes | + |
Compare the closest 3 against the 8MBX51 →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.