B&C 5MDN38
Thiele-Small parameters
| Nominal size | 5" |
|---|---|
| Impedance | 8 Ω |
| Fs | 175 Hz |
| Qts | 0.31 |
| Qes | 0.36 |
| Qms | 2.3 |
| Vas | 1.4 L |
| Sd | 95 cm² |
| Xmax | 3.5 mm |
| Re | 5.5 Ω |
| Bl | 11.1 T·m |
| Mms | 8 g |
| Pe | 90 W |
| Sensitivity | 97 dB |
Alignment hint
| EBP | 486 · ported |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 0.3 L |
EBP > 100: favours a ported (bass-reflex) alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| Beyma 5G40Nd/N | 140 -35 | 0.45 +0.14 | 1.4 = | 3 -0.5 | 92 -5 | usable | Xmax 3 mm < 3.5 mm: lower excursion-limited SPL | + |
| B&C 5MDN38 | 230 +55 | 0.48 +0.17 | 0.8 -0.6 | 3.5 = | 96 -1 | risky | 16 Ω vs 8 Ω: amp load changes | + |
| BMS 5N160 | 113 -62 | 0.43 +0.12 | 2.57 +1.17 | 5 +1.5 | 91 -6 | risky | 16 Ω vs 8 Ω: amp load changes | + |
| Faital PRO 5PR160 | 90 -85 | 0.31 = | 3.7 +2.3 | 5.1 +1.6 | 92 -5 | risky | + | |
| Sica 5 M 1.5 PL | 145 -30 | 0.51 +0.2 | 2 +0.6 | 1.5 -2 | 93.7 -3.3 | risky | Xmax 1.5 mm < 3.5 mm: lower excursion-limited SPL | + |
| Faital PRO 5PR120 | 100 -75 | 0.27 -0.04 | 4.2 +2.8 | 3.1 -0.4 | 100 +3 | risky | Xmax 3.1 mm < 3.5 mm: lower excursion-limited SPL | + |
| BMS 5S117 | 95 -80 | 0.42 +0.11 | 3.25 +1.85 | 5 +1.5 | 91 -6 | risky | 16 Ω vs 8 Ω: amp load changes | + |
| B&C 5NDL38 | 80 -95 | 0.36 +0.05 | 4.3 +2.9 | 3.5 = | 91 -6 | risky | + | |
| Sica 5 N 1.5 PL | 110.6 -64.4 | 0.56 +0.25 | 3 +1.6 | 3 -0.5 | 91 -6 | risky | Xmax 3 mm < 3.5 mm: lower excursion-limited SPL | + |
| LaVoce WSF051.02 | 106 -69 | 0.6 +0.29 | 3.26 +1.86 | 3.1 -0.4 | 91.5 -5.5 | risky | 60 W vs 90 W: lower power handling · Xmax 3.1 mm < 3.5 mm: lower excursion-limited SPL | + |
Compare the closest 3 against the 5MDN38 →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.