B&C 18 TBX 100 (prodance)
Thiele-Small parameters
| Nominal size | 18" |
|---|---|
| Impedance | 8 Ω |
| Fs | 36.6 Hz |
| Qts | 0.406 |
| Qes | 0.43 |
| Qms | 7.41 |
| Vas | 198 L |
| Sd | 1134 cm² |
| Xmax | 9 mm |
| Re | 5.14 Ω |
| Bl | 21.8 T·m |
| Mms | 172.3 g |
| Pe | 1200 W |
| Sensitivity | 97.4 dB |
Alignment hint
| EBP | 85 · flexible |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 97.4 L |
EBP 50-100: works in either a sealed or ported alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| Fane 18XLS | 36 -0.6 | 0.407 = | 187 -11 | 9.3 +0.3 | 97 -0.4 | close | + | |
| Fane COLOSSUS 18XLS | 36 -0.6 | 0.407 = | 187 -11 | 9.3 +0.3 | 97 -0.4 | close | + | |
| Faital PRO 18HP1042 | 38 +1.4 | 0.41 = | 191.9 -6.1 | 9 = | 98 +0.6 | close | + | |
| Beyma 18LEX1600/ND-8 | 35 -1.6 | 0.39 -0.02 | 205 +7 | 10.4 +1.4 | 96.8 -0.6 | close | + | |
| Sica 18 S 4 PL | 36.2 -0.4 | 0.39 -0.02 | 189 -9 | 8 -1 | 97.3 -0.1 | close | Xmax 8 mm < 9 mm: lower excursion-limited SPL | + |
| B&C 18NBX100 | 35 -1.6 | 0.38 -0.03 | 198 = | 10 +1 | 96.5 -0.9 | close | + | |
| Faital PRO 18HP1030 | 35 -1.6 | 0.41 = | 185.5 -12.5 | 12.45 +3.45 | 98 +0.6 | close | + | |
| Celestion POWER PRO X18 | 34.8 -1.8 | 0.379 -0.03 | 188.9 -9.1 | 8.6 -0.4 | 96.6 -0.8 | close | Xmax 8.6 mm < 9 mm: lower excursion-limited SPL | + |
| Faital PRO 18HP1060 | 35 -1.6 | 0.37 -0.04 | 200.3 +2.3 | 12.45 +3.45 | 98 +0.6 | close | + | |
| Beyma 18G550 | 36 -0.6 | 0.374 -0.03 | 210 +12 | 8.1 -0.9 | 97.8 +0.4 | close | 900 W vs 1200 W: lower power handling · Xmax 8.1 mm < 9 mm: lower excursion-limited SPL | + |
Compare the closest 3 against the 18 TBX 100 (prodance) →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.