← all drivers

B&C 12NW76

12" · 4 Ω · 500 W · 98 dB · datasheet ↗

Thiele-Small parameters

Nominal size12"
Impedance4 Ω
Fs43 Hz
Qts0.15
Qes0.15
Qms3.75
Vas64.5 L
Sd522 cm²
Xmax8 mm
Re3.4 Ω
Bl22 T·m
Mms82 g
Pe500 W
Sensitivity98 dB

Alignment hint

EBP287 · ported
Sealed Vb (Qtc ≈ 0.71)≈ 3 L

EBP > 100: favours a ported (bass-reflex) alignment.

Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.

Substitute candidates

DriverFs (Hz)QtsVas (L)Xmax (mm)Sens (dB)FitNotesCompare
B&C 12NW7640 -30.16 +0.0176 +11.58 =98.5 +0.5close8 Ω vs 4 Ω: amp load changes+
Oberton 12NB40043.58 +0.580.18 +0.0370.45 +5.955.25 -2.7598 =usable8 Ω vs 4 Ω: amp load changes · Xmax 5.25 mm < 8 mm: lower excursion-limited SPL+
Oberton 12NMB60041.03 -1.970.134 -0.0270.8 +6.35.25 -2.7599 +1usable8 Ω vs 4 Ω: amp load changes · Xmax 5.25 mm < 8 mm: lower excursion-limited SPL+
18 Sound 12ND94049 +60.2 +0.0564.8 +0.37.6 -0.4100 +2usable8 Ω vs 4 Ω: amp load changes · Xmax 7.6 mm < 8 mm: lower excursion-limited SPL+
B&C 12 NW 7640 -30.163 +0.0176 +11.54.8 -3.298.3 +0.3usable8 Ω vs 4 Ω: amp load changes · Xmax 4.8 mm < 8 mm: lower excursion-limited SPL+
Beyma 12"P80/Fe V248 +50.21 +0.0661 -3.57.5 -0.599 +1usable8 Ω vs 4 Ω: amp load changes · Xmax 7.5 mm < 8 mm: lower excursion-limited SPL+
Oberton 12NB45046.46 +3.460.204 +0.0572.57 +8.077.75 -0.25100 +2usable8 Ω vs 4 Ω: amp load changes · Xmax 7.75 mm < 8 mm: lower excursion-limited SPL+
RCF LF12P90347 +40.23 +0.0865 +0.57 -197.8 -0.2usable8 Ω vs 4 Ω: amp load changes · Xmax 7 mm < 8 mm: lower excursion-limited SPL+
Beyma 12P80ND V250 +70.163 +0.0165 +0.54.5 -3.5100.7 +2.7usable8 Ω vs 4 Ω: amp load changes · Xmax 4.5 mm < 8 mm: lower excursion-limited SPL+
JBL 2254J46.6 +3.60.159 +0.0173.6 +9.13.9 -4.197 -1usable16 Ω vs 4 Ω: amp load changes · Xmax 3.9 mm < 8 mm: lower excursion-limited SPL+

Compare the closest 3 against the 12NW76 →

Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.

Used in enclosures (0)

No enclosure in the catalog uses this driver yet.