B&C 10PS26
Thiele-Small parameters
| Nominal size | 10" |
|---|---|
| Impedance | 8 Ω |
| Fs | 54 Hz |
| Qts | 0.29 |
| Qes | 0.33 |
| Qms | 2.9 |
| Vas | 38 L |
| Sd | 320 cm² |
| Xmax | 5.5 mm |
| Re | 6 Ω |
| Bl | 14.1 T·m |
| Mms | 33 g |
| Pe | 350 W |
| Sensitivity | 96 dB |
Alignment hint
| EBP | 164 · ported |
|---|---|
| Sealed Vb (Qtc ≈ 0.71) | ≈ 7.7 L |
EBP > 100: favours a ported (bass-reflex) alignment.
Rules of thumb from T/S parameters only. Verify against a real simulation before cutting wood.
Substitute candidates
| Driver | Fs (Hz) | Qts | Vas (L) | Xmax (mm) | Sens (dB) | Fit | Notes | Compare |
|---|---|---|---|---|---|---|---|---|
| B&C 10 PS 26 | 54 = | 0.296 +0.01 | 38 = | 5.5 = | 96 = | close | + | |
| Sica 10 N 3 PL | 51 -3 | 0.29 = | 40.5 +2.5 | 5.5 = | 96.1 +0.1 | close | + | |
| B&C 10 PS 26 (prodance) | 53.4 -0.6 | 0.267 -0.02 | 39.5 +1.5 | 5.4 -0.1 | 96.8 +0.8 | close | Xmax 5.4 mm < 5.5 mm: lower excursion-limited SPL | + |
| Sica 10 Fe 3 CP | 52 -2 | 0.31 +0.02 | 38.6 +0.6 | 5 -0.5 | 95.9 -0.1 | close | Xmax 5 mm < 5.5 mm: lower excursion-limited SPL | + |
| 18 Sound 10W500 | 53 -1 | 0.29 = | 45.2 +7.2 | 5.5 = | 98 +2 | close | + | |
| Faital PRO 10PR310 | 55 +1 | 0.31 +0.02 | 40.3 +2.3 | 4.92 -0.58 | 97 +1 | close | 4 Ω vs 8 Ω: amp load changes · Xmax 4.92 mm < 5.5 mm: lower excursion-limited SPL | + |
| RCF MB 10N251 | 55 +1 | 0.271 -0.02 | 38.8 +0.8 | 4.6 -0.9 | 97.4 +1.4 | close | Xmax 4.6 mm < 5.5 mm: lower excursion-limited SPL | + |
| SICA 10 FE 3 CP v2017 | 52 -2 | 0.307 +0.02 | 38.6 +0.6 | 4.2 -1.3 | 95.8 -0.2 | close | Xmax 4.2 mm < 5.5 mm: lower excursion-limited SPL | + |
| Sica 10 K 3 PL | 50.6 -3.4 | 0.26 -0.03 | 40 +2 | 6.5 +1 | 96.7 +0.7 | close | + | |
| Monacor SP-10A/302PA | 55 +1 | 0.298 +0.01 | 40 +2 | 4 -1.5 | 96.3 +0.3 | close | Xmax 4 mm < 5.5 mm: lower excursion-limited SPL | + |
Compare the closest 3 against the 10PS26 →
Ranked on parameter similarity only (Qts, Fs, Vas, Xmax, sensitivity). Same nominal size required. A hint, not a simulation, model the swap before cutting or buying.
Used in enclosures (0)
No enclosure in the catalog uses this driver yet.